Справочник Пользователя для Festool PM561608

18 

Carvex PS420 Series

 WARNING! Any maintenance or repair work 

that requires opening of the motor or gear hous-

ing should be carried out only by an authorized 

Customer Service Center (see your dealer for 

information on locating a service center).

 WARNING! To reduce the risk of electrocution or 

other personal injury, always unplug the tool from 

the power supply outlet or remove the battery 

before performing any maintenance or repair work 

on the tool.

  NOTICE: Do not use compressed air to clean the 

motor housing of the tool, as you could inject for-

eign objects into the motor through the ventilation 

openings.

  NOTICE: Certain cleaning agents and solvents are 

harmful to plastic parts. Some of these include, but 

are not limited to: Gasoline, Acetone, Methyl Ethyl 

Ketone (MEK), Carbonyl Chloride, cleaning solutions 

containing Chlorine, Ammonia, and household clean-

ers containing Ammonia.

Dust and debris from some materials can be extremely 

abrasive and cause components within the saw to wear 

prematurely. It is important to keep moving parts cleared of 

abrasive dusts.

 

►

As a general rule, keep the saw clean of all dust and 

debris. Even soft-wood dust can be abrasive over time.

 

►

Examine all moving parts for dust and debris.

 

►

Keep the blade area and dust extraction port clean of 

debris. Debris can cause wear and reduce the effective-

ness of the dust extraction system.

 WARNING! The stroboscopic function of the LED 

light may make it difficult to determine the blade 

position, or give the appearance that the blade is 

not moving. 

 WARNING! Never look directly into the LED lights. 

The lights are very bright and may damage your 

vision.

The LED work lights have 3 programmable settings. These 

are stroboscopic, steady-on, and off. To reduce the likeli-

hood of the bright LED lights from shining in the operator’s 

eyes, the lights will automatically turn off any time the saw 

is rotated slightly past vertical toward the upside down posi-

tion. These three operating modes are described below:
Stroboscopic: The stroboscopic function means that the 

LEDs will operate in unison with the speed of the sawblade 

stroke. This synchronous operation will make the sawblade 

appear stationary, instead of a blur of motion. The purpose 

of this stopped-motion appearance is to make it easier to 

follow a pencil line.
The stroboscopic effect is active only when the blade speed 

is above approximately 2100 strokes per minute. This 

means the frequency range of the light is 35 to 63 Hertz. 
Steady-On: In the steady-on mode, the LED lights will be 

active and steady-on anytime the saw is operating, except 

when the saw is turned upside down.
Off: In this mode, the LED lights are disabled.

 WARNING! Do not perform this adjustment with a 

sawblade installed in the jigsaw. This adjustment 

may result in the saw starting unexpectedly.

1.  Remove the sawblade from the saw as described on 

. 

2.  Hold the saw in such a manner that when the LED lights 

turn on, they will not shine directly into your eyes.

3.  Simultaneously press and hold both left and right barrel 

power switches until the saw beeps.

 

►

If the saw turns on, turn it back off and try again. 

The saw may turn on if both switches are not pressed 

simultaneously.

 

►

It will take approximately 10 seconds for the saw to 

beep from the time you first pressed the two switches.

 

►

The LED lights may or may not come on after the saw 

beeps, depending on the previous program mode. 

4.  When the saw beeps, release both power switches.
5.  Press and release the right-hand power switch to cycle 

through the 3 programming options.

 

►

The LED lights will indicate the current program mode. 

They will flash if in stroboscopic mode. They will be 

steady-on for steady-on mode. They will be off for the 

off-mode.

6.  When the desired program mode is selected, Pres and 

release the left-hand power switch to exit program-mode.

Right Power 

Switch

Left Power 

Switch