Справочник Пользователя для Panasonic TYPE E
“ZNR” Transient/Surge Absorbors, Type E, Type CK, SC
– EC130 –
Fuse
ZNR
Varistor
Varistor
Protected
Equipment
2.2 Circuit Design 1
(Selection of Varistor Voltage Rating)
2.2.1 General Precautions
In selection of Varistor Voltage Ratings for line
protection, following general precautions shall be
taken in your consideration;
(1) Maximum operating voltage shall be lower than
protection, following general precautions shall be
taken in your consideration;
(1) Maximum operating voltage shall be lower than
the specifi ed “Maximum Allowable Voltage” of the
Varistor applied.
Varistor applied.
(2)
Some reasonable margin is required against
fl uctuation of the primary AC line Voltage where
the Varis tor is applied for preventing mechanical
and/or electrical failures of the device.
fl uctuation of the primary AC line Voltage where
the Varis tor is applied for preventing mechanical
and/or electrical failures of the device.
2.2.2 Across-the-Line Use
(Line to Line surge protection)
(Line to Line surge protection)
● Select the ZNR Varistors recommended in Table 1.
Notes: Because the primary line voltage temporarily
Notes: Because the primary line voltage temporarily
rises due to load unbalance of separately
wired loads, short circuit between the live line
and the nutral line or LC resonance at switching
for a capacitive load, ZNR Varistors with
✽ are recommended for AC120 V or 240 V
applications. (See Table 1)
wired loads, short circuit between the live line
and the nutral line or LC resonance at switching
for a capacitive load, ZNR Varistors with
✽ are recommended for AC120 V or 240 V
applications. (See Table 1)
2.2.3 Line to Ground Use
(Line to Ground Surge pro tec tion)
(Line to Ground Surge pro tec tion)
● Select the ZNR Varistors recommended in Table 1.
Notes: When 500 V insulation resistance test of the
Notes: When 500 V insulation resistance test of the
circuits employing ZNR Varistor is conducted,
the ZNR Varistor shall be removed after
getting approv
the ZNR Varistor shall be removed after
getting approv
al from the customer, or the
ZNR Varistor
✽ ✽ with the Maximum Allowable
Voltage ex
ceeding to the test voltage shall be
applied. (See Table 1)
When AC1000 V or 1200 V dielectric with
standing test is conducted, ZNR Varistors
shall be removed after getting approval
from the customer according to the relevant
regulations, or ZNR Varistor
shall be removed after getting approval
from the customer according to the relevant
regulations, or ZNR Varistor
✽ ✽ ✽ with the
Maximum Allowable Volt age exceeding to the
test voltage shall be applied. (See Table 1)
test voltage shall be applied. (See Table 1)
2.3 Circuit Design 2 (Fusing Varistors)
2.3.1 When a line current of equipment is higher than
the recommended current rating of the fuse in
Table 2, the location of the fuse shall be arranged
according to Fig 2.
Table 2, the location of the fuse shall be arranged
according to Fig 2.
Fig. 2 Alternative Fuse Location/placement
for Varis tor Pro tec tion
2.4 Environmental Conditions
(1) The ZNR Varistors shall not be exposed
outdoors, because of being designed for in
doors
use.
(2)The ZNR Varistors shall not be operated beyond
the Specifi
ed Operating Temperature Range and
shall not be exposed to direct sunlight and heating
part of equipment.
part of equipment.
(3)The ZNR Varistors shall not be operated under
se vere conditions of high temperatures and high
humidities such as places exposed to rain, wind
and vapor.
humidities such as places exposed to rain, wind
and vapor.
(4)The ZNR Varistors shall be free from dust, salty
wind and atomospheres polluted by corrosive
gas.
gas.
2.5 Precautions for Assemblies and Handlings
2.5.1 Solvent Cleaning
Organic solvents such as thinner and acetone
etc. shall not be applied to the ZNR Varistors for
preventing deterioration of the external coating or
molding resin.
etc. shall not be applied to the ZNR Varistors for
preventing deterioration of the external coating or
molding resin.
2.5.2 Abnormal Mechanical Stresses
Abnormal mechanical stresses beyond the spec
i fi ed
values such as strong falling shocks, ribrations and
bending/pulling forces, shall be kept minimum to
preventmechanical/electrical
failures of the devices.
bending/pulling forces, shall be kept minimum to
preventmechanical/electrical
failures of the devices.
2.5.3 Plastic Molding
If another plastic molding is applied to the ZNR
Varistors on your option, the infl uences on reliability
of the ZNR Varistors shall be carefully investigated
in your equipment.
Varistors on your option, the infl uences on reliability
of the ZNR Varistors shall be carefully investigated
in your equipment.
2.6 Long Term Storage
(1) The ZNR Varistors shall not be stored under
severe conditions of high temperatures and high
humidities. Store them indoors under 40 °C max.
and 75 %RH max. Use them within one year, if
stored beyond the limit, check the solderbility before
use.
humidities. Store them indoors under 40 °C max.
and 75 %RH max. Use them within one year, if
stored beyond the limit, check the solderbility before
use.
(2)The ZNR Varistors shall not be stored under
corrosive ato mospheres such as hydrogen
sulfi de, sulfurous acid, chlorine and ammonia.
sulfi de, sulfurous acid, chlorine and ammonia.
(3)The ZNR Varistors shall not be exposed to direct
sunlight and shall not be stored under dew
formation.
2.7 Regarding to “Safety Regulations of the
Varistors”
Varistors”
In case of applications to UL and CSA standards,
refer to “Application Notes for UL and CSA Recognized”
ZNR “Varistors”
refer to “Application Notes for UL and CSA Recognized”
ZNR “Varistors”
2.8 Parallel Capacitances of the ZNR Varistors
The ZNR Varistors have relatively high capacitances
specifi ed in the individual specifi
specifi ed in the individual specifi
cations, special
consideration shall be taken into account in
a p p l i c at i o n s to h ig h f re q u e n cy t ra n s m i s s i o n
lines or circuits.
a p p l i c at i o n s to h ig h f re q u e n cy t ra n s m i s s i o n
lines or circuits.
Apr. 2008
00