Справочник Пользователя для 3com 8
12
Connecting Workstations and Other
Equipment to Your Hub
Equipment to Your Hub
WARNING: Please read the ‘Important Safety
Information’ section before you start.
Information’ section before you start.
WARNHINWEIS: Bitte lesen Sie den Abschnitt
‘Wichtige Sicherheitsinformationen’ sorgfältig durch,
bevor Sie das Gerät einschalten.
‘Wichtige Sicherheitsinformationen’ sorgfältig durch,
bevor Sie das Gerät einschalten.
AVERTISSEMENT: Veuillez lire attentivement la
section “Consignes importantes de sécurité” avant de
mettre en route.
section “Consignes importantes de sécurité” avant de
mettre en route.
CAUTION: Do not power the hub off and on quickly.
Wait about five seconds between power cycles.
Wait about five seconds between power cycles.
Connect workstations and other equipment to any of the
hub’s 10BASE-T RJ-45 ports using 10BASE-T cables.
hub’s 10BASE-T RJ-45 ports using 10BASE-T cables.
To connect a 10BASE-T cable, simply slot the connector into
the relevant RJ-45 port. When the connector is fully in, its
latch locks it into place. To disconnect the cable, push the
connector’s latch in and remove it.
the relevant RJ-45 port. When the connector is fully in, its
latch locks it into place. To disconnect the cable, push the
connector’s latch in and remove it.
If you are using port 4 to connect to a workstation
using a straight-through TP cable, ensure the
Uplink/Normal switch is set to Normal (out).
using a straight-through TP cable, ensure the
Uplink/Normal switch is set to Normal (out).
The hub detects all port connections, so you can start using
your network immediately. When you need more ports,
simply add more OfficeConnect hubs.
your network immediately. When you need more ports,
simply add more OfficeConnect hubs.
Connecting Transceivers to the AUI Port
You can connect a 10Mbps Ethernet transceiver to your hub
(Hub 4C only), using a standard AUI cable. Connect one
end of the cable to the transceiver and the other end to the
AUI port on the hub’s rear panel. This automatically disables
the 10BASE-2 port, and activates the AUI/COAX LED to
show the external transceiver is in use. Engage the slide
locks at both ends of the AUI cable.
(Hub 4C only), using a standard AUI cable. Connect one
end of the cable to the transceiver and the other end to the
AUI port on the hub’s rear panel. This automatically disables
the 10BASE-2 port, and activates the AUI/COAX LED to
show the external transceiver is in use. Engage the slide
locks at both ends of the AUI cable.
Connecting OfficeConnect Ethernet Hubs
Together
Together
You can increase the number of workstations that can
connect to your network by adding more OfficeConnect
hubs. You can use either 10BASE-T or 10BASE-2 (Hub 4C
only) to do this.
connect to your network by adding more OfficeConnect
hubs. You can use either 10BASE-T or 10BASE-2 (Hub 4C
only) to do this.
Do not connect the same two hubs together using
both 10BASE-T and 10BASE-2. This causes a network
loop.
both 10BASE-T and 10BASE-2. This causes a network
loop.
If you do not use the 10BASE-2 port, you do not
need to connect a terminator (end piece) to it. If the
AUI port is not used and a terminator is not
connected to the 10BASE-2 port, the port partitions
and the Coax Status LED lights yellow. This is correct
operation.
need to connect a terminator (end piece) to it. If the
AUI port is not used and a terminator is not
connected to the 10BASE-2 port, the port partitions
and the Coax Status LED lights yellow. This is correct
operation.
3C16700.book Page 12 Tuesday, July 13, 1999 9:59 AM