Справочник Пользователя для Mitsubishi Electronics XL21
REV 2.4
67
1.8.4. DISPLAY
This adjustment is normally unnecessary. The optimum value is automatically renewed
when H./V. DISPLAY POS. are changed.
Used to designate a display area on screen by manual. It can tweak an unmatched image
linkage between screens.
•
when H./V. DISPLAY POS. are changed.
Used to designate a display area on screen by manual. It can tweak an unmatched image
linkage between screens.
•
H.POSITION: The horizontal starting position of the display area.
•
V.POSITION: The vertical starting position of the display area.
•
H.SIZE: The horizontal display size. It can erase a noise on a side of images.
•
V.SIZE: The vertical display size. It can erase a noise on the top or bottom of images.
[Procedure]
1. Select DISPLAY in the display memory menu.
2. Adjust each item.
Note:
• It will be automatically renewed when H./V. DISPLAY POS. are changed.
• H.SIZE and V.SIZE are not required to adjust when H./V. DISPLAY POS is set 1/1 to display
1. Select DISPLAY in the display memory menu.
2. Adjust each item.
Note:
• It will be automatically renewed when H./V. DISPLAY POS. are changed.
• H.SIZE and V.SIZE are not required to adjust when H./V. DISPLAY POS is set 1/1 to display
an un-scaled image.
1.8.5. DIGITAL
OUT
Used to designate a signal to be output from the digital output terminal. The initial setting is
SCREEN. A registered input memory for the input board can be optionally selected. Input
memories for the main input cannot be designated.
•
SCREEN. A registered input memory for the input board can be optionally selected. Input
memories for the main input cannot be designated.
•
DISABLE: No signal to be output.
•
SCREEN: Current displaying image on screen is output.
•
1 – 128: The adjustments in the designated input memory 1 – 128 are reflected on the
output signal.
output signal.
[Procedure]
1. Select DIGITAL OUT in the display memory menu.
2. Select a signal to be output from the digital output terminal.
Note: Different input memories in the same input port cannot be designated as both the digital
out and the on screen display simultaneously. Also it is unable to designate COMPOSITE and
Y/C as well.
1. Select DIGITAL OUT in the display memory menu.
2. Select a signal to be output from the digital output terminal.
Note: Different input memories in the same input port cannot be designated as both the digital
out and the on screen display simultaneously. Also it is unable to designate COMPOSITE and
Y/C as well.
1.8.6. SCREEN
MODE
Used to set when the aspect ratio of an input signal is different from the screen to display.
•
•
NORMAL: The original aspect ratio is maintained to display whole image at the center of the
screen. The margins are displayed black.
screen. The margins are displayed black.
•
TRIMMING: The original aspect ratio is maintained and the image is enlarged to fill the entire
screen. An HDTV image with 16:9 aspect ratio is cut the right and left edges.
screen. An HDTV image with 16:9 aspect ratio is cut the right and left edges.
•
FULL: The aspect ratio is adjusted to fill the whole image in the entire screen. The image
with 16:9 aspect ratio appears stretching vertically.
with 16:9 aspect ratio appears stretching vertically.
[Procedure]
1. Select SCREEN MODE in the display memory menu.
2. Select NORMAL, TRIMMING or FULL.
Note: The original aspect ratio is set in ASPECT-RATIO menu (chapter 1.7.5.5, on page 64).
Even if the effective image area is 16:9, when it is set 4:3 in ASPECT-RATIO menu, the image is
processed as 4:3.
1. Select SCREEN MODE in the display memory menu.
2. Select NORMAL, TRIMMING or FULL.
Note: The original aspect ratio is set in ASPECT-RATIO menu (chapter 1.7.5.5, on page 64).
Even if the effective image area is 16:9, when it is set 4:3 in ASPECT-RATIO menu, the image is
processed as 4:3.