Справочник Пользователя для Netopia CLI 874
2-34 Command Line Interface Commands Reference
Ethernet Interface Static Client Address Translation Commands
Note:
The commands in this section are suppor ted beginning with firmware version 8.5.
interface ethernet lan_inter face_id scat enable [ yes | no ]
show interface ethernet lan_inter face_id scat enable
show interface ethernet lan_inter face_id scat enable
These commands allow you to enable, disable, or show the status of static client address translation on the
specified LAN inter face. This feature allows a statically addressed host whose address falls outside of the LAN
subnet(s) to simply plug in and get online without any manual configuration on either the host or the Motorola
Netopia
specified LAN inter face. This feature allows a statically addressed host whose address falls outside of the LAN
subnet(s) to simply plug in and get online without any manual configuration on either the host or the Motorola
Netopia
®
Router.
If scat enable is set to yes, statically addressed LAN hosts that have an address outside of LAN subnets will be
able to communicate via the Router’s WAN inter face to the Internet.
able to communicate via the Router’s WAN inter face to the Internet.
Suppor ted static IP address values must fall outside of the Router's LAN subnet(s).
Ethernet Interface VRRP Commands
Note:
The commands in this section are suppor ted beginning with firmware version 8.5.
A Vir tual Router is a software abstraction consisting of a group of two or more hardware routers protecting one
or more IP addresses. One of the routers is designated as the Master, while the others are backups. VRRP is a
protocol that provides redundancy to routers within a local area network by allowing alternate paths for a PC
without changing the IP address or MAC address by which the PC knows its gateway.
or more IP addresses. One of the routers is designated as the Master, while the others are backups. VRRP is a
protocol that provides redundancy to routers within a local area network by allowing alternate paths for a PC
without changing the IP address or MAC address by which the PC knows its gateway.
A Vir tual Router cannot be enabled unless it is populated with a Vir tual ID and a Vir tual IP address. The Vir tual
Router index star ts from 1 (one). Two vir tual routers can be configured per LAN inter face.
Router index star ts from 1 (one). Two vir tual routers can be configured per LAN inter face.
interface ethernet id ip vrrp vrouter id vrid [ 1... 255 ]
show interface ethernet id ip vrrp vrouter id vrid
show interface ethernet id ip vrrp vrouter id vrid
These commands allow you to specify or display an ID (vrid) for the Vir tual Router. vrid values may be in the
range 1 – 255.
range 1 – 255.
interface ethernet id ip vrrp vrouter id vrip ip-addr
show interface ethernet id ip vrrp vrouter id vrip
show interface ethernet id ip vrrp vrouter id vrip
These commands allow you to specify or display an IP address for the Vir tual Router.
interface ethernet id ip vrrp vrouter id priority [ 1... 255 ]
show interface ethernet id ip vrrp vrouter id priority
show interface ethernet id ip vrrp vrouter id priority
These commands allow you to specify or display a priority for the Vir tual Router. The default value is 100, if not
the owner of the vir tual IP address. priority values may be in the range 1 – 255.
the owner of the vir tual IP address. priority values may be in the range 1 – 255.
interface ethernet id ip vrrp vrouter id adv-intvl [ 1... 255 ]
show interface ethernet id ip vrrp vrouter id adv-intvl
show interface ethernet id ip vrrp vrouter id adv-intvl
These commands allow you to specify or display an adver tisement inter val in seconds. The default value is one
second; adv-intvl values may be in the range 1 – 255.
second; adv-intvl values may be in the range 1 – 255.