Справочник Пользователя для Symbol Technologies PDT 8100
38
P
D
T
8
1
0
0
S
e
r
i
e
s
w
i
t
h
W
i
n
d
o
w
s
M
o
b
i
l
e
2
0
0
3
f
o
r
P
o
c
k
e
t
P
C
s
Radio Modules
The PDT 8100 series terminals may contain an approved radio module. These
modules are identified below.
modules are identified below.
• PDT 8133:Novatel CDPD Radio Module, Type: NRM-6831
• PDT 8137:Motorola G18 GSM/GPRS Radio Module, Type: G18
• PDT 8142:Symbol Compact Flash RLAN (2Mbps DSSS) radio card, Type(s):
• PDT 8137:Motorola G18 GSM/GPRS Radio Module, Type: G18
• PDT 8142:Symbol Compact Flash RLAN (2Mbps DSSS) radio card, Type(s):
LA-302T
• PDT 8146:Symbol Compact Flash RLAN (11Mbps DSSS) radio card, Type(s):
LA-412T
FCC RF Exposure Guidelines
Safety Information
The device complies with Internationally recognised standards covering Specific
Absorption Rate (SAR) related to human exposure to electromagnetic fields from
radio devices.
The device complies with Internationally recognised standards covering Specific
Absorption Rate (SAR) related to human exposure to electromagnetic fields from
radio devices.
Reducing RF Influence - Use Properly
It is advisable to use the device only in the normal operating position and it is
recommended that no part of the human body be allowed to come too close to the
antenna during operation of the equipment.
It is advisable to use the device only in the normal operating position and it is
recommended that no part of the human body be allowed to come too close to the
antenna during operation of the equipment.
Phones (placed to ear or used with headset)
To comply with RF safety requirements use the specific belt clip. All other belt clips
should be avoided and may not comply with RF safety requirements. The FCC has
granted an Equipment Authorization for these model phones with all reported SAR
levels evaluated as in compliance with the FCC RF emission guidelines. SAR
information on these model phones is on file with the FCC and can be found under
the Display Grant section of http://www.fcc.gove/oet/fccid.
To comply with RF safety requirements use the specific belt clip. All other belt clips
should be avoided and may not comply with RF safety requirements. The FCC has
granted an Equipment Authorization for these model phones with all reported SAR
levels evaluated as in compliance with the FCC RF emission guidelines. SAR
information on these model phones is on file with the FCC and can be found under
the Display Grant section of http://www.fcc.gove/oet/fccid.
Handheld Devices
This device was tested for typical body-worn operation. The use of third-party belt-
clips, holsters, and similar accessories should not contain metallic components in its
assembly. The use of these accessories that do not satisfy these requirements may
not comply with FCC RF exposure compliance requirements, and should be avoided.
This device was tested for typical body-worn operation. The use of third-party belt-
clips, holsters, and similar accessories should not contain metallic components in its
assembly. The use of these accessories that do not satisfy these requirements may
not comply with FCC RF exposure compliance requirements, and should be avoided.
Laser Devices
Symbol devices using lasers comply with US 21CFR1040.10, and IEC825-1:1993,
EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels
on the device.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other than
those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels
on the device.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other than
those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
6598801a.fm Page 38 Monday, December 8, 2003 2:01 PM