Инструкции Пользователя для Mitsubishi Electronics ws-65413
20
21
Connecting MonitorLink™, NetCommand® IR Emitter
Other A/V Device
1
F
er
ri
te
C
o
re
A/V Receiver
D I G I T A L
S U R R O U N D
S
CH
2
or
IR EMITTER
R
NetCommand IR
REPEATER
use with
NetCommand
controlled devices
use with
non-NetCommand
controlled devices
Figure 14. Connecting MonitorLink
Figure 15. Connecting IR Emitters
WS-48413, WS-55413, WS-65413
MonitorLink/DVI
(Figure 14)
1. Connect a MonitorLink/DVI cable from the
TV back panel to the Mitsubishi HD Receiver/
Controller back panel.
2. Connect the MonitorLink Control/RS-232 cable
from the TV back panel to the Mitsubishi HD
Receiver/Controller back panel.
3. Connect the L (left) and R (right) audio cables
from the HDTV receiver to AUDIO LEFT and
AUDIO RIGHT on the MonitorLink section of
the TV back panel.
NOTE:
The 29 pin MonitorLink/DVI and
RS-232 cables can be found at your local
electronics store.
IR Emitter Repeater and
NetCommand® IR
(Figure 15)
(WS-, WS-, WS-)
The two IR jacks labeled REPEATER are not used by
NetCommand, but will repeat any IR command received
by the TV. The NetCommand® IR jacks are used by
NetCommand to control external devices. They both
connect the same way:
connect the same way:
1. Connect one of the IR emitters to one IR
EMITTER jacks on the TV back panel.
2. Place the IR emitter cable under or on top of each
A/V device. Place the IR lens directly in front of
the A/V device infrared signal receiver, usually
located behind the front translucent panel of the
receiver.
3. If you are connecting to only one A/V device,
place the unused transmitter in an out-of-the-way
location.
4. For permanent installation of the IR emtter cable,
use the included double sided adhesive tape to
secure the body of the emitter to the A/V receiver,
DVD player, Cable box, etc...
Note: The TV back panel and connections shown here are for reference only and may vary by model.
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
WS-48413, WS-55413, WS-65413
back panel
back panel
403XF-5K
1
1
2
2
OUTPUTS
TO
DISPLAY
DISPLAY
1
2
3
4
MONITOR
PIP
INPUT
TO
AV RECEIVER
AC IN
DIGITAL AUDIO
OUTPUT
MonitorLink
TM
/DVI
MonitorLink
TM
CONTROL/RS-232
IR OUTPUT
NetCommand
R
S-VIDEO
VIDEO
AUDIO
LEFT
LEFT
AUDIO
RIGHT
RIGHT
White
Red
Mitsubishi HD-5000
receiver/controller back panel
receiver/controller back panel
3
White
Red
3
ferrite
core
core
ferrite
core
core
Y
G
Pb
B
P r
R
V
H
DTV
(Y PbPr/ GBRH V )
480 i / 480P /1080 i
MONITORLINK
TM
/DVI
MONITORLINK
TM
CONTROL
RS-232C
40
3X
F-
5K
Do not use the IR emitter connections with
devices that can receive the remote control
signal directly, as the signals can interfere with
each other.
signal directly, as the signals can interfere with
each other.
CAUTION:
To assure continued FCC compliance,
the user must use a shielded video interface cable with
bonded ferrite cores at both ends, when using the
MonitorLink/DVI input.
bonded ferrite cores at both ends, when using the
MonitorLink/DVI input.