Справочник Пользователя для Toshiba HD-S23
APPENDIX 2
TROUBLESHOOTING
Problem Solution
(1) The receiver front panel power indicator
doesn't light up, and no message on the
front panel
front panel
(a) Check the AC mains supply and make sure the power plug is
well plugged into a stable power outlet
(b) Press the “Power” button on the front panel to see if the LED
display is on.
(c) Press the “Power” button on the remote control to see if the LED
display is on.
(2) Message is shown on the front panel but
no picture on TV screen
(a) Make sure the connection between the receiver and TV matches the
mode your TV should be set to. For instance, if you use a RCA cable
you may choose external video input mode in TV.
you may choose external video input mode in TV.
(b) Check the brightness level of your TV.
Zinwell to-do:
Add OUT1/OUT2 descriptions here.
(3) Poor picture quality
(a) Check the antenna and make sure it is aligned to the correct
direction. Use the receiver's "MANUAL SETUP" page to check the
signal's BER and RF Level when aligning the antenna.
signal's BER and RF Level when aligning the antenna.
(b) If you use any kind of amplifier to boost the signal level, please
check whether it works well, and ask help from the antenna
installer.
installer.
(4) No sound
(a) Check the receiver and your TV's volume are properly set and not in
“Mute" mode.
(b) Check the audio connectors are correctly and firmly connected.
(c) Make sure the receiver is switched to the correct Audio mode:
(c) Make sure the receiver is switched to the correct Audio mode:
Dolby® Digital or PCM.
(d) Rescan this channel by using "MANUAL SETUP".
(e) Switch to other channels for confirmation on audio.
(e) Switch to other channels for confirmation on audio.
(5) No picture
(a) Check the video cables are correctly and firmly connected.
(b) Rescan this channel by using "MANUAL SETUP".
(c) Switch to other channels for confirmation on video.
(b) Rescan this channel by using "MANUAL SETUP".
(c) Switch to other channels for confirmation on video.
(6) Not all channels are available after using
“AUTO SCAN” when installing the
receiver for the first time
receiver for the first time
Try "MANUAL SETUP" to scan these missing channels.
This problem is caused by unexpected frequency offset, for instance,
in Sunshine Coast Australia, channels 47 and 65 are transmitted on
662.625 and 788.625 MHz by 125KHz offset to the legitimate
frequencies 662.5 and 788.5 MHz. HD-S23 can receive them by “AUTO
SCAN” most of the times, but we suggest that you use “MANAL
SETUP” when installing the receiver for the first time. Once the signal is
picked up by the receiver, all the transmission parameters will be stored
in the receiver's memory.
This problem is caused by unexpected frequency offset, for instance,
in Sunshine Coast Australia, channels 47 and 65 are transmitted on
662.625 and 788.625 MHz by 125KHz offset to the legitimate
frequencies 662.5 and 788.5 MHz. HD-S23 can receive them by “AUTO
SCAN” most of the times, but we suggest that you use “MANAL
SETUP” when installing the receiver for the first time. Once the signal is
picked up by the receiver, all the transmission parameters will be stored
in the receiver's memory.
(7) Not all channels are available after using
“QUICK SCAN”
(a) Try "AUTO SCAN" to scan all the channels.
(b) If you still cannot get some channels please use “MANUAL
(b) If you still cannot get some channels please use “MANUAL
SETUP” to scan them one by one.
(8) Cannot lock signal by using “MANUAL
SETUP”
(a) Check the frequency you entered is exactly the centre frequency of
the wanted channel.
(b) Please refer to solutions in item (3) on pp. XX.
(9) No Teletext
Make sure the channel you are watching carries
Teletext information
from I-PLATE.
(10) Cannot receive channels after moving
the receiver between cities (for instance
from Melbourne to Sydney)
from Melbourne to Sydney)
Please refer to pp. XX for reinstallation.
(11) RCU button pressed not responding.
Replace remote control unit batteries.
A
pp
en
dic
es
35