Справочник Пользователя для Toshiba 26HL66
17
HL66 (E/F) Web 213:276
Chapter 4: Setting up your TV
Programming channels into the
TV’s channel memory
TV’s channel memory
When you press < or , on the remote control or TV control
panel, your TV will stop only on the channels you programmed
into the TV’s channel memory.
Follow the steps below to program channels into the TV’s
channel memory.
panel, your TV will stop only on the channels you programmed
into the TV’s channel memory.
Follow the steps below to program channels into the TV’s
channel memory.
Programming channels automatically
Your TV can automatically detect all active channels in your
area and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels in the channel memory.
area and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels in the channel memory.
Note:
• You must configure the antenna input source before
• You must configure the antenna input source before
programming channels (
- page 16).
• If the Antenna input signal type is set to Cable, the automatic
channel programming process erases channels that were
previously programmed into the TV’s channel memory.
previously programmed into the TV’s channel memory.
• If the Antenna input signal type is set to Antenna, the
automatic channel programming process adds newly found
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV’s memory.) To remove an Antenna
source channel from the memory, you must manually
delete it.
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV’s memory.) To remove an Antenna
source channel from the memory, you must manually
delete it.
• To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
remote control.
• Programming channels when the antenna input is
configured for Cable will take substantially longer than when
the antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should
not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
the antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should
not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
To program channels automatically:
1
Make sure you have configured the antenna input source
(
(
-
page 16).
2
Press Y and open the Setup menu.
3
Highlight Installation and press T.
4
(A new set of Installation menu icons appears, as shown
below.) Open the Terrestrial menu, highlight Channel
Program, and press T.
below.) Open the Terrestrial menu, highlight Channel
Program, and press T.
5
Highlight ANT 1 and then press T to start automatic
channel programming.
channel programming.
The TV will automatically cycle through all the antenna
channels, and store all active channels in the channel
memory. While the TV is cycling through the channels,
the message “Scanning channels, please wait” appears (as
shown above).
channels, and store all active channels in the channel
memory. While the TV is cycling through the channels,
the message “Scanning channels, please wait” appears (as
shown above).
6
To cancel channel programming, either press O or
highlight Abort in the on-screen display and press T.
When channel programming is finished, press < or , to
view the programmed channels.
highlight Abort in the on-screen display and press T.
When channel programming is finished, press < or , to
view the programmed channels.
Manually adding and deleting channels
in the channel memory
in the channel memory
After automatically programming channels into the channel
memory, you can manually add or delete individual channels.
memory, you can manually add or delete individual channels.
To add or delete channels in the channel memory:
1
Press Y and open the Setup menu.
2
Highlight Installation and press T.
CH RTN
ENTER
EXIT
Navigate
Select
Back
Exit
Installation
Sleep Timer
PC Settings
Setup
PC Audio
Auto
Power-Saving
HDMI Audio
No
Power-On Mode
CH RTN
ENTER
EXIT
Navigate
Select
Back
Exit
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
ANT 1 Antenna
Scanning channels, please wait ...
Abort
52%
(continued)
2632HL66_EN.book Page 17 Tuesday, July 18, 2006 3:47 PM