Справочник Пользователя для Fostex D-160
D-160 Owner's Manual (Saving and loading data)
106
9
10
11
12
13
14
15
5
6
7
8
16
1
2
3
4
5
6
7
8
1
2
9~16
1~8
9~6
DATA
OUTPUT
INPUT
1~8
OPTICAL
INPUT
OUTPUT
THRU
ANALOG IN
ANALOG OUT
SCSI
MIDI
TO RAIN OR MOISTURE.
SHOCK. DO NOT EXPOSE THIS EQUIPMENT
TO REDUCE THE RISK OF FIRE OR ELECTRIC
WARNING:
NE PAS OUVRIR
:RISQUE DE CHOC ELECTRIQUE
AVIS
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
4
3
2. Loading the data using DATA IN
* Restore the initial settings on the D-160.
* Set the same sampling rate on the external digital device and the D-160.
Connecting the external device
Connect DATA INPUT 1-8 connectors of the D-160 to the digital output connectors on the
external digital device.
external digital device.
<Notes>
* The D-160 has DATA INPUT connectors for an S/P DIF digital signal (OPTICAL) and for an adat
digital signal. These connectors have the same shape but carry different information.
* Use the DATA INPUT 1-8 connector to load data. Do not use the DATA INPUT 9-16 connector.
* When save/load using DAT and adat, independent save/load in 8 track units is possible. In
* When save/load using DAT and adat, independent save/load in 8 track units is possible. In
this case, the data in 8 track units are not distinguished as track 1~8 or 9~16 but simply
handled as eight track data. Therefore, as this 8 track data is compatible with D-90 if it is in 8
track units (any one combination of 1~8, 9~16 or 17~24), data saved from D-160 can be
loaded in tracks 1~8 of the D-90. In this case, data in the tracks which was not loaded will
remain intact.
handled as eight track data. Therefore, as this 8 track data is compatible with D-90 if it is in 8
track units (any one combination of 1~8, 9~16 or 17~24), data saved from D-160 can be
loaded in tracks 1~8 of the D-90. In this case, data in the tracks which was not loaded will
remain intact.
• If the external device has only COAXIAL type (RCA) digital I/O connectors, connect an
optional COP-1 (optical/coaxial converter) to use an S/P DIF digital signal.
• Connecting both output and input connectors on the D-160 to the input and output
connectors on the external digital device respectively may generate a digital loop.
Refer to “4-3. Connecting a digital mixer” on page "65" for more information.
Refer to “4-3. Connecting a digital mixer” on page "65" for more information.
Setting up an external device
1. Setup the external device so that it can output a digital signal.
2. Locate the beginning of the pilot signal recorded in the saved data.
* Refer to the instruction manual that came with your external digital device for details.
Executing the load operation
You will use the “Load PGM ?” menu in Setup mode.
* Input format available: adat, DAT, SCSI
* Programs available: P1 - P99
* You can load one saved Program at a time.
1. Press the DISP SEL key to select “SETUP” (“SETUP” will flash) and press the EXECUTE/YES
key. (“SETUP” will light up.)
The D-160 will enter the Setup mode.
2. Use the JOG dial to select “Load PGM ?” (“?” will flash.).
3. Press the EXECUTE/YES key.
The message “Load Device?” and the type of digital signal to be loaded (“DAT,” “adat,” or “SCSI”)
will flash on the display.
will flash on the display.
DIGITAL OUT
DATA INPUT 1-8
External Digital Equipment (DAT or RD-8 or Adat)
D-160