Справочник Пользователя для Toshiba D-R17DTKB
EN
75
Introducti
o
n
C
onnecti
o
ns
Basi
c Setup
P
la
ybac
k
Ed
it
it
in
g
Othe
rs
Fu
ncti
ncti
on
S
S
et
u
p
Re
cor
d
cor
d
in
g
• When you set the “Video Out” setting, make sure
that the AV1(TV) Scart socket is connected to your
TV with Scart cable.
TV with Scart cable.
1
Select the desired setting using
[
[
U / D], then press [ENTER/OK].
• If your TV is compatible with progressive scanning
(576p/480p), connect the TV to the COMPONENT
VIDEO OUTPUT jacks of this unit and select
“Component Progressive (P)” and set your TV to the
progressive scan mode.
VIDEO OUTPUT jacks of this unit and select
“Component Progressive (P)” and set your TV to the
progressive scan mode.
• If your TV is not compatible with progressive scan,
select “Component Interlace (I)” for component
connection, or select “SCART(RGB)” for Scart cable
connection.
connection, or select “SCART(RGB)” for Scart cable
connection.
• Refer to page 20 for more details.
Only if you select the “Component Progressive (P)”,
proceed to step 2. If you select “Component Interlace
(I)” or “SCART(RGB)”, your setting is activated.
proceed to step 2. If you select “Component Interlace
(I)” or “SCART(RGB)”, your setting is activated.
2
Using [
L / P] to select “Yes”. Press
[ENTER/OK].
Final confirmation window will appear.
3
Using [
U / D] to select “Yes”. Press
[ENTER/OK] within 15 seconds.
Your setting is activated.
Note
• If the Progressive Scan image is distorted, you can
cancel Progressive Scan by pressing and holding
[SETUP] for more than 3 seconds during DVD
playback. The “Video Out” setting will be
“SCART(RGB)”.
[SETUP] for more than 3 seconds during DVD
playback. The “Video Out” setting will be
“SCART(RGB)”.
• When changing the Video Out setting (“SCART
(RGB)”, “Component Interlace (I)” or “Component
Progressive (P)”), connect to the corresponding jack
on the TV. If the setting is changed, for example, to
“SCART (RGB)” while the COMPONENT VIDEO
OUTPUT jacks are used to connect to the TV, a
distorted video signal may be output.
Progressive (P)”), connect to the corresponding jack
on the TV. If the setting is changed, for example, to
“SCART (RGB)” while the COMPONENT VIDEO
OUTPUT jacks are used to connect to the TV, a
distorted video signal may be output.
DivX
®
1
In stop mode, press [SETUP]. Select
“General Setting” using [
“General Setting” using [
U / D],
then press [ENTER/OK].
2
Select “DivX” using [
U / D], then
press [ENTER/OK].
3
Select the desired item using
[
[
U / D], then press [ENTER/OK].
For DivX
®
VOD, refer to page 50 in details.
DivX Subtitle (Default: OFF)
Select the desired setting using
[
[
U / D], then press [ENTER/OK].
4
When you finish with the setting,
press [SETUP] to exit.
press [SETUP] to exit.
Video Out
SCART (RGB)
Component Progressive (P)
Component Interlace (I)
Component Progressive (P)
Component Interlace (I)
Activating progressive scan:
Check your TV has progressive scan
and connect with component video cable.
Check your TV has progressive scan
and connect with component video cable.
NOTE:
If there is no picture or picture is
distorted after selecting “Yes”,
wait about 15 seconds for autorecovery.
distorted after selecting “Yes”,
wait about 15 seconds for autorecovery.
Activate?
No
Yes
Confirm again to use progressive scan.
If Picture is good, select “Yes”.
If Picture is good, select “Yes”.
No
Yes
HDMI
Reset All
Reset All
General Setting
Display
Video
Video
Clock
Channel
DivX
Channel
DivX
Recording
Playback
DivX
®
VOD
DivX Subtitle
DivX Subtitle
OFF
English
French
Spanish
German
Italian
Swedish
English
French
Spanish
German
Italian
Swedish
E7J70BD_EN.book Page 75 Monday, May 7, 2007 3:31 PM