Листовка для VTech LS6125

Install the telephone base and charger(s) as 

shown below.

Install  the  battery  as  shown  below.  After 

installing  the  battery,  you  might  be  able 

to  make  and  receive  short  calls.  For  best 

performance, charge the handset battery for 

at least 16 hours before use.

 

Use  only  the  power  adapter(s)  and 

battery(ies) supplied with your VTech 

telephone.
For  complete  feature  instructions, 

please refer to your user’s manual.

1.

2.

The telephone is preset with a greeting that 

answers  calls  with 

message after the tone.”  You can use this 

preset  announcement,  or  replace  it  with 

your own. 
To record your own announcement:

Press 

ANNC while the telephone is not 

in  use  and  the  system  will  announce 

RECORD.”
Press 

RECORD  and  the  system 

announces, 

STOP when you are done.”
After  the  tone,  speak  towards  the 

microphone  at  the  bottom  front  of 

the  telephone  base  from  about  nine              

inches away.
Press 

/PLAY/STOP when finished.

The answering system will automatically 

play the newly recorded announcement. 

Press 

/PLAY/STOP to stop the playback 

at anytime.

Press 

PLAY/STOP to play messages and 

stop playback.
Press 

X/DELETE  while  a  message  is 

playing to delete it.
Press 

/SKIP to skip to the next message.

Press 

/REPEAT  to  repeat  the  current 

message.
Press 

VOL  /  to raise or lower playback 

volume.

1.

2.

3.

4.
5.

•

•

•
•

•

If your product is not working properly:

Refer to the 

Troubleshooting section of 

the user’s manual.

Visit our website at www.vtechphones.

com or call 1 (800) 595-9511. In Canada, 

go to www.vtechcanada.com or 1 (800) 

267-7377.

•

•

96-006809-010-100   

Telephone base

Telephone line cord

Electrical outlet 

not controlled 

by a wall switch

Telephone base 

power adapter 

(large)

Telephone 

wall jack

DSL filter (not 

included) required 

if you have DSL 

high-speed 

Internet service 

Charger

Charger 

adapter 

(small)

Press 

/FLASH or  .

Dial the number.

Dial the number.
Press 

/FLASH or  .

Press 

/

FLASH,   or any of the dialing 

keys (

0-9, #, *).

Press 

OFF/CLEAR or put the handset in 

the telephone base or charger.

The  answering  system  must  be  turned  on 

to  answer  and  record  messages.  Press          

ANS ON/OFF to turn the answering system 

on  or  off.  When  the  answering  system  is 

turned  on,  it  will  announce 

answered,” and the 

ANS ON/OFF light will be 

on. When the answering system is turned off, 

it will announce 

“Calls will not be answered,” 

and the 

ANS ON/OFF light will be off.

1.
2.

1.
2.

•

•

1

2

FLASH

CLEAR

SELECT

MENU

CID

VOL

CHARGE light

3

4

Plug the battery securely 

into the plug inside 

the handset battery 

compartment, matching 

the color-coded label.

Place the battery with the 

label 

THIS SIDE UP facing 

up and the wires inside 

the battery compartment. 

Align the cover flat 

against the battery 

compartment, then slide 

it upwards until it clicks 

into place.

Charge the handset by 

placing it in the telephone 

base or charger. The 

CHARGE light will be 

on when the handset is 

charging.