Справочник Пользователя для Toshiba 65HM167
35
HM67 (E/F) Web 213:276
Chapter 5: Setting up your TV
Setting the Power-On Mode feature
You can select either Power-Saving or Fast mode.
If you select Power-Saving mode and you turn off the TV, it
can take several seconds for the picture to appear when you turn
on the TV again. Power-Saving mode saves more power than
Fast mode. See “Specifications” on page 66 for details.
If you select Fast mode and the TV is turned off, the TV will
stay in Standby mode for several minutes (see Note below). If
the TV is turned on from Standby mode, the full picture
appears immediately.
If you select Power-Saving mode and you turn off the TV, it
can take several seconds for the picture to appear when you turn
on the TV again. Power-Saving mode saves more power than
Fast mode. See “Specifications” on page 66 for details.
If you select Fast mode and the TV is turned off, the TV will
stay in Standby mode for several minutes (see Note below). If
the TV is turned on from Standby mode, the full picture
appears immediately.
To set the Power-On Mode feature:
1
Press
Y and open the Setup menu.
2
Highlight Power-On Mode and press c.
3
Press b or B to select either Fast or Power-Saving and
press
press
T.
Note: If Power-On Mode is set to Fast and you turn off the TV,
the following will occur for a few minutes:
the following will occur for a few minutes:
• The screen (lamp) lights dimly; and
• The fans continue to run.
This is a function of the Power-On Fast Shutdown mode and is
not a TV malfunction. If you do not prefer this, set the Power-
On Mode feature to Power-Saving.
• The fans continue to run.
This is a function of the Power-On Fast Shutdown mode and is
not a TV malfunction. If you do not prefer this, set the Power-
On Mode feature to Power-Saving.
When the Power-On Mode feature is set to Power-Saving, if
you repeatedly turn the TV on and off in a short period of time,
the useful service life of the lamp may be shorter than the
average useful service life (
you repeatedly turn the TV on and off in a short period of time,
the useful service life of the lamp may be shorter than the
average useful service life (
- page 63).
Viewing the digital signal meter
You can view the digital signal meter in the ANT digital TV
input source only.
input source only.
To view the digital signal meter:
1
Press
Y and open the Setup menu.
2
Highlight Installation and press
T.
3
A new set of Installation menu icons will appear, as shown
below. Open the Terrestrial menu, highlight Signal
Meter, and press
below. Open the Terrestrial menu, highlight Signal
Meter, and press
T.
4
Press BbC c to select the antenna input and digital
channel whose signal you want to check.
channel whose signal you want to check.
Note: The physical digital channel number listed in the
Signal Meter screen may not correspond to a virtual TV
channel number. Contact your local broadcasters to
obtain the RF channel numbers for your local digital
stations.
Signal Meter screen may not correspond to a virtual TV
channel number. Contact your local broadcasters to
obtain the RF channel numbers for your local digital
stations.
To close the screen and return to the Terrestrial
menu:
menu:
Highlight Done and press
T.
To return to normal viewing:
Press
O.
IMPORTANT NOTICE ABOUT HOT LAMP RESTART
When the TV has been powered on long enough for the
lamp unit to get hot, it may take several minutes for the
picture to appear in the following situations:
lamp unit to get hot, it may take several minutes for the
picture to appear in the following situations:
•
When the Power-On Mode feature is set to Power-
Saving and you turn the TV off and then on again within
a few minutes; or
Saving and you turn the TV off and then on again within
a few minutes; or
•
If the TV is on when a short-term power failure, power
surge, or other similar power failure occurs, such that
the TV loses and regains power within a few minutes.
surge, or other similar power failure occurs, such that
the TV loses and regains power within a few minutes.
This is a property of DLP
®
TV lamp technology and is
NOT a sign of malfunction.
If this occurs, the yellow LED on the TV front panel will
blink (and the blue LED will be lit solid) until the TV is
finished restarting the lamp and the normal picture
appears. If both LEDs are blinking, you will need to turn
the TV off and then on again to restart the lamp.
If this occurs, the yellow LED on the TV front panel will
blink (and the blue LED will be lit solid) until the TV is
finished restarting the lamp and the normal picture
appears. If both LEDs are blinking, you will need to turn
the TV off and then on again to restart the lamp.
Installation
Sleep Timer
PC Settings
Setup
Power-On Mode
Fast
Power-Saving
Fast
Installation
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Signal Meter
Physical Digital Channel
4
Virtual Digital Channel
Done
Advanced
4-1
Signal Locked
0
0
Peak
50HM67_EN.book Page 35 Thursday, March 29, 2007 11:28 AM