Справочник Пользователя для Mitsubishi Electronics WD-62825
18
19
Additional connection cables are
not provided with the TV. They are
available at most electronic stores.
available at most electronic stores.
IMPORTANT
Connecting a Wall Outlet Cable or Cable Box
Wall Outlet Cable
(can be used with a CableCARD™)
Figure 1
Figure 1
It is very important to connect the incoming
cable for your primary viewing source to ANT-1,
especially for CableCARD™ use.
cable for your primary viewing source to ANT-1,
especially for CableCARD™ use.
1. Connect the primary incoming coaxial lead cable to
ANT-1 MAIN on the TV back panel.
2. For an optional secondary antenna source, connect
an antenna (or cable) to ANT-2 AUX.
3. If you have subscribed to a CableCARD™ service,
the CableCARD can now be inserted into the
CableCARD SLOT. Using a phillips screwdriver,
remove the CableCARD cover screws. Insert the
CableCARD, then replace the cover and screws.
CableCARD SLOT. Using a phillips screwdriver,
remove the CableCARD cover screws. Insert the
CableCARD, then replace the cover and screws.
The top of the card should face in the direction the
CARD TOP arrow indicates.
Additional CableCARD information is on page 20.
Figure 1. Wall Outlet Cable
Cable Box
Figure 2
3 coaxial cables and one two-way RF splitter are required.
3 coaxial cables and one two-way RF splitter are required.
These are not included with the TV.
It is very important to connect the incoming
cable for your primary viewing source to ANT-1,
especially for CableCARD™ use.
cable for your primary viewing source to ANT-1,
especially for CableCARD™ use.
1. Connect the incoming cable to IN on an RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to IN on the cable box.
4. Connect one coaxial cable from OUT on the cable
box to ANT-2 AUX on the TV back panel.
Note: Net Command® will assume that your
Cable Box is connected as shown above. Also,
that Channel 3 is the default output channel
for the cable box. If either the connections or
output channel are different, use the Change
option of Edit NetCommand to apply the
changes.
that Channel 3 is the default output channel
for the cable box. If either the connections or
output channel are different, use the Change
option of Edit NetCommand to apply the
changes.
Figure 2. Connecting a Cable Box
Cable Box
back panel section
Incoming
Cable
IN
OUT
IN
O
U
T
O
U
T
T
W
O
W
A
Y
S
P
LI
T
T
E
R
1.
4.
2.
3.
3.
4.
2.
IR EMITTER
NetCommand
R
DVI
Analog Audio
DTV/
CABLE/
VHF/
UHF
ANT-2
AUX
ANT-1
MAIN
M-LINK
CONTROL/
RS-232C
HDMI
M-LINK
L
R
TV back panel section
CableCARD
TM
SLOT
(cover removed)
3.
DIGITAL
AUDIO
IR EMITTER
NetCommand
R
DVI
Analog Audio
DTV/
CABLE/
VHF/
UHF
ANT-2
AUX
ANT-1
MAIN
M-LINK
CONTROL/
RS-232C
HDMI
M-LINK
L
R
TV back panel section
CARD
TOP
C
ab
leC
AR
D
SL
O
T
TM
1. Primary
Wall Outlet
Cable
Cable
2. Optional
Secondary
Antenna
or Cable
Antenna
or Cable