Справочник Пользователя для Mitsubishi Electronics WD-62825
22
23
Connecting an Antenna or Wall Outlet Cable to a VCR (Audio &
Video)
Antenna or Wall Outlet Cable to a
VCR (Audio & Video)
Figure 5
A two-way RF splitter, 3 coaxial cables, right and left audio
cables and a S-Video or Video cables are required. These are
not included with the TV.
not included with the TV.
1. Connect the incoming cable or Antenna to IN on the
RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the VCR back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel.
4. To use the TV speakers with the VCR, connect a
set of audio cables from AUDIO OUT on the VCR
back panel to INPUT-1 AUDIO-LEFT (MONO) and
AUDIO-RIGHT on the TV back panel. The red cable
connects to the R (right) channel and the white
cable connects to the L (left) channel. If your VCR
is mono (non-stereo), connect only the white (left)
cable.
Note:
NetCommand®
will assume your
VCR is connected
to inputs as
shown on this
page. If you use
any other inputs
for your VCR or
add a second
VCR, this change
must match in
the NetCommand
system. See Edit
NetCommand... in
Chapter 3 for more
information.
NetCommand®
will assume your
VCR is connected
to inputs as
shown on this
page. If you use
any other inputs
for your VCR or
add a second
VCR, this change
must match in
the NetCommand
system. See Edit
NetCommand... in
Chapter 3 for more
information.
Figure 5. Connecting a VCR to an Antenna or Wall Outlet Cable
5. Connect either an S-Video or Video cable from
VIDEO OUT on the VCR back panel to INPUT-1
VIDEO on the TV back panel. Only one type of
video cable should be connected. S-Video is
recommended, if available.
6. For NetCommand® controlled recordings, connect
a set of audio cables from AUDIO IN on the VCR
back panel to MONITOR OUTPUT AUDIO/VIDEO 1
AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV
back panel. The red cable connects to the R (right)
channel and the white cable connects to the L (left)
channel.
7. Complete the NetCommand controlled recordings
connections by connecting a Video cable from
VIDEO IN on the VCR back panel to MONITOR
OUTPUT AUDIO/VIDEO 1 on the TV back panel.
IR EMITTER
NetCommand
R
INPUT-1
AUDIO 2
AUDIO/VIDEO 1
AUDIO
L(MONO)
R
INPUT-2
DIGITAL
AUDIO
PC
VGA/SVGA/XGA/
720p
60 Hz
PC-
AUDIO
PC-
INPUT
M-LINK
CONTROL/
RS-232C
HDMI
M-LINK
IEEE1394
INPUT/OUTPUT
VIDEO
S-VIDEO
MONITOR
OUTPUT
L
R
DTV/
CABLE/
VHF/
UHF
ANT-2
AUX
ANT-2
AUX
4.
6.
IN
O
U
T
O
U
T
T
W
O
W
A
Y
S
P
LI
T
T
E
R
Incoming
Cable
Cable
1.
2.
3.
TV back panel section
MONITOR
OUTPUT
Attach only one cable type
S-Video
recommended
if available
recommended
if available
�� �����
4.
6.
VCR back panel
If your VCR has a video channel
or RF ON/OFF switch, set it to OFF.
or RF ON/OFF switch, set it to OFF.
5.
5.
7.
7.
3.
5.
2.
DVI
Analog Audio
L
R
DTV/
CABLE/
VHF/
UHF
ANT-1
MAIN
INPUT-1
AUDIO
L(MONO)
R
VIDEO
S-VIDEO
AUDIO/VIDEO 1