Справочник Пользователя для Mitsubishi Electronics WD-62825
30
31
When Connecting IEEE 1394 Devices
• Do not loop the last device in the chain back
to the TV. When the device chain is looped,
the TV may not be able to work with the other
devices.
the TV may not be able to work with the other
devices.
• Place devices that have only a mechanical (two-
position) power switch at the end of the chain
or leave the power switch in the On position.
or leave the power switch in the On position.
When turned Off, IEEE 1394 signals may not
be able to pass through the device to other
devices.
devices.
• Place devices with the slowest communication
speed at the end of the chain. Sometimes
the communication speed will be marked
near the IEEE 1394 connector with an “S”
number. The higher the number, the faster
the communication speed. This TV has a
communication speed of S400. Devices with
slow communication speed can interfere
with IEEE 1394 signals from faster devices.
When using NetCommand to set up a digital
recording between a faster and slower device,
the slower device should be the source and the
faster device should be the sync.
the communication speed will be marked
near the IEEE 1394 connector with an “S”
number. The higher the number, the faster
the communication speed. This TV has a
communication speed of S400. Devices with
slow communication speed can interfere
with IEEE 1394 signals from faster devices.
When using NetCommand to set up a digital
recording between a faster and slower device,
the slower device should be the source and the
faster device should be the sync.
• Do not use an IEEE 1394 cable longer than 15
feet between each device.
• This TV is an IEEE 1394a Device. IEEE 1394b
is currently under development. This system
will provide for longer distances and multi-
room applications. Included in the IEEE
will provide for longer distances and multi-
room applications. Included in the IEEE
1394b systems are IEEE 1394a to IEEE 1394b
converters to maintain compatibility with this TV
and other IEEE 1394a devices.
and other IEEE 1394a devices.
Connecting Compatible IEEE 1394 Devices
Compatible IEEE 1394 Devices
It is possible to connect devices to the TV that have IEEE
1394 connectors but are not compatible with the TV or with
the NetCommand® control system. Areas of compatibility
to consider are:
to consider are:
1. Digital Video Signals
The TV is able to decode MPEG2 video. Other types
of digital video, such as DV video provided by some
camcorders, must be decoded by the source device
and sent to the TV as analog video or S-Video. If the
camcorder uses a compatible digital control system,
the IEEE 1394 cable can still provide control for the
camcorder while the TV is viewing the analog video or
S-Video signals.
camcorders, must be decoded by the source device
and sent to the TV as analog video or S-Video. If the
camcorder uses a compatible digital control system,
the IEEE 1394 cable can still provide control for the
camcorder while the TV is viewing the analog video or
S-Video signals.
2. Digital Audio Signals
When received with video signals, the TV is able to
decode Dolby Digital signals and MPEG audio signals.
Other types of digital audio as provided by some digital
recording devices, such as MP3 audio and DTS audio,
cannot be decoded by the TV when received over IEEE
decode Dolby Digital signals and MPEG audio signals.
Other types of digital audio as provided by some digital
recording devices, such as MP3 audio and DTS audio,
cannot be decoded by the TV when received over IEEE
1394.
The TV may not be able to pass incompatible digital
audio signals on the coaxial digital audio output,
however these signals may pass on the IEEE 1394 cable
to other devices.
to other devices.
3. Digital Control Signal
The TV is able to act as the control center for IEEE 1394
audio/video devices, such as VCRs, A/V Discs, tuners,
cable boxes and amplifiers that are compatible with the
following IEEE 1394 control standards.
cable boxes and amplifiers that are compatible with the
following IEEE 1394 control standards.
•
EIA-775 is designed for tuning devices such as cable
boxes allowing the device to send simple graphics.
However, this standard does not allow the TV to
However, this standard does not allow the TV to
control the cable box by IEEE 1394.
•
AV/C (Audio Video Control) is designed to provide
basic controls such as play, stop, channel selection
and volume, as appropriate for the device.
Some devices may be a combination of two or more
types of devices. For example, there may be a
types of devices. For example, there may be a
recording device that is also a tuning device. Each
portion of the device is called a sub-unit. When you
select a device on the Device Selection menu that
has sub-units, a pop-up menu will appear so you can
select which sub-unit section you wish to use.
portion of the device is called a sub-unit. When you
select a device on the Device Selection menu that
has sub-units, a pop-up menu will appear so you can
select which sub-unit section you wish to use.