Справочник Пользователя для Mitsubishi Electronics WD-52627
22
Chapter 2. Connecting
Connecting External Devices and NetCommand
®
Setup
Model
M-VR800 &
M-VR1000
Model
M-VR900 &
M-VR700
Model
Lifestyle ®28
Model
AVR-2700
Model
DTR-9.1
Model
VR-2080
Model
SR8200
Model
VSX-D557
Model
VSX-9TX
Model
RSX-1065
Model
STR-DE825
Model
RV-X2095
Model
RX-V2200
Device Audio Output
to
AV Receiver Inputs by Name
VCR
VCR 1
VCR
VCR
VCR-1
Video 1
Video 1
VCR1
VCR/Tape VCR 1/DVR
Video 2
Video 1
VCR 1
VCR 1
Satellite Receiver
Aux
Cable/DBS
AUX
CD
Video 3
Video 3
DSS
CD
SAT
Video 4
TV/DBS
TV/DBS
D-TV/LD
DVD Player
DVD
DVD
(built-in)
DVDVDP
DVD
Video 4
DVD
LD/SAT
DVD/LD
Video 5
TAPE/MD
CD
DVD
TV Monitor Output
(& Digital Audio)
(& Digital Audio)
TV
TV
TV
TV/DBS
Video 4
Video 4
TV
DVD/TV
TV
Video 1
DVD/LD
DVD/LD CBL/SAT
Chart 2
Mitsubishi 1 Mitsubishi 2
Bose
Denon
Integra
Kenwood Marantz Pioneer 1
Pioneer 2
Rotel
Sony
Yamaha 1 Yamaha 2
AV
Receiver
TV
Device to be
connected
stereo and/or digital
audio cables
video and stereo
audio cables
stereo and/or digital audio cables
*3&NJUUFST
NetCommand is able to control many current audio and video devices by sending remote control signals from the TV
to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio
video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or
to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio
video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or
learned Audio/Video (A/V) Receivers to the correct input used with each device. It is important that the inputs on the
TV and A/V receiver back panels match the NetCommand setup that is displayed on screen.
To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this
chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio
and video) and to the A/V receiver (audio) as shown in the figure below. If you connect devices to inputs other than the
ones shown as presets, you must change the NetCommand setup accordingly. See the Edit NetCommand information
starting on page 47.
assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio
and video) and to the A/V receiver (audio) as shown in the figure below. If you connect devices to inputs other than the
ones shown as presets, you must change the NetCommand setup accordingly. See the Edit NetCommand information
starting on page 47.
The following charts show which preset inputs you should use on the TV and A/V receiver.
Chart 1 shows the default TV inputs existing in NetCommand.
Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand.
Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand.
Chart 1
NetCommand Default Device Audio and Video Outputs to TV Inputs
Cable for CableCARD™ Service
ANT-1
Antenna/Cable (digital/analog)
ANT-1 if primary viewing source,
ANT-2 if secondary viewing source
ANT-2 if secondary viewing source
Cable box
COMPONENT-1
VCR
Input-1
Satellite Receiver (SAT)
Input-2
Camcorder
Input-3 (on front panel)
DVD Player
COMPONENT-2
PC
HDMI-2
After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used
for connecting each device, custom name devices, add devices not included in the presets above or delete devices
no longer used. See Edit NetCommand. See Helpful Hints at the end of this chapter for additional information on
device setup.
no longer used. See Edit NetCommand. See Helpful Hints at the end of this chapter for additional information on
device setup.