Справочник Пользователя для Silicon Laboratories C8051F342
C8051F340/1/2/3/4/5/6/7
184
Rev. 0.5
USB Register Definition 16.18. E0CNT: USB0 Endpoint 0 Data Count
16.11. Configuring Endpoints1-3
Endpoints1-3 are configured and controlled through their own sets of the following control/status registers:
IN registers EINCSRL and EINCSRH, and OUT registers EOUTCSRL and EOUTCSRH. Only one set of
endpoint control/status registers is mapped into the USB register address space at a time, defined by the
contents of the INDEX register (USB Register Definition 16.4).
IN registers EINCSRL and EINCSRH, and OUT registers EOUTCSRL and EOUTCSRH. Only one set of
endpoint control/status registers is mapped into the USB register address space at a time, defined by the
contents of the INDEX register (USB Register Definition 16.4).
Endpoints1-3 can be configured as IN, OUT, or both IN/OUT (Split Mode) as described in
The endpoint mode (Split/Normal) is selected via the SPLIT bit in register EINCSRH.
When SPLIT = ‘1’, the corresponding endpoint FIFO is split, and both IN and OUT pipes are available.
When SPLIT = ‘0’, the corresponding endpoint functions as either IN or OUT; the endpoint direction is
selected by the DIRSEL bit in register EINCSRH.
selected by the DIRSEL bit in register EINCSRH.
16.12. Controlling Endpoints1-3 IN
Endpoints1-3 IN are managed via USB registers EINCSRL and EINCSRH. All IN endpoints can be used
for Interrupt, Bulk, or Isochronous transfers. Isochronous (ISO) mode is enabled by writing ‘1’ to the ISO bit
in register EINCSRH. Bulk and Interrupt transfers are handled identically by hardware.
for Interrupt, Bulk, or Isochronous transfers. Isochronous (ISO) mode is enabled by writing ‘1’ to the ISO bit
in register EINCSRH. Bulk and Interrupt transfers are handled identically by hardware.
An Endpoint1-3 IN interrupt is generated by any of the following conditions:
1.
An IN packet is successfully transferred to the host.
2.
Software writes ‘1’ to the FLUSH bit (EINCSRL.3) when the target FIFO is not empty.
3.
Hardware generates a STALL condition.
16.12.1.Endpoints1-3 IN Interrupt or Bulk Mode
When the ISO bit (EINCSRH.6) = ‘0’ the target endpoint operates in Bulk or Interrupt Mode. Once an end-
point has been configured to operate in Bulk/Interrupt IN mode (typically following an Endpoint0
SET_INTERFACE command), firmware should load an IN packet into the endpoint IN FIFO and set the
INPRDY bit (EINCSRL.0). Upon reception of an IN token, hardware will transmit the data, clear the
INPRDY bit, and generate an interrupt.
point has been configured to operate in Bulk/Interrupt IN mode (typically following an Endpoint0
SET_INTERFACE command), firmware should load an IN packet into the endpoint IN FIFO and set the
INPRDY bit (EINCSRL.0). Upon reception of an IN token, hardware will transmit the data, clear the
INPRDY bit, and generate an interrupt.
Bit7:
Unused. Read = 0; Write = don’t care.
Bits6–0: E0CNT: Endpoint 0 Data Count
This 7-bit number indicates the number of received data bytes in the Endpoint 0 FIFO. This
number is only valid while bit OPRDY is a ‘1’.
number is only valid while bit OPRDY is a ‘1’.
R
R
R
R
R
R
R
R
Reset Value
-
E0CNT
00000000
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
USB Address:
0x16