Инструкции для Barco R9002240

Содержание

• Safety instructions

  1
• On safety

  1
• On installation

  1
• On servicing

  1
• On cleaning

  1
• On repacking

  1
• On illumination

  1
• Location and Functions of Control

  2
• Rear panel terminology

  2
• Front panel terminology

  2
• Control panel terminology

  2
• a. The Local Keypad

  2
• b. RCU control panel terminology

  2
• Connections

  3
• AC Power (mains) Cord Connection

  3
• Power Check

  3
• Switching On/Off

  3
• Signal Input Connection to the Projector :

  3
• Connecting a Composite Video source to port 1.

  3
• Connecting a S-Video or Video source to port 2.

  3
• Connecting a RGB Analog source to port 3.

  3
• Connecting a RGB Analog source to port 4/5.

  3
• Connecting a RGB Analog source with Tri-level sync to port 4/5.(option)

  3
• Connecting a Component Video source to port 4/5.

  3
• Connecting a Component Video source with Tri-level sync to port 4/5.(Opion)

  3
• Peripheral equipment

  3
• Connecting a RCVDS 05 switcher to the projector

  3
• Connecting a VS05 switcher to the projector.

  3
• Connecting an IR Remote Receiver to the projector

  3
• Controlling

  4
• Battery installation in the RCU.

  4
• How to use your RCU

  4
• Projector Address

  4
• How to display a projector address?

  4
• How to program an address into the RCU?

  4
• Input selection

  4
• Analog Picture Controls

  4
• Controlling chained projectors.

  4
• Start up of the Adjustment Mode

  5
• Adjustment Mode

  5
• Random Access Adjustment Mode

  6
• Starting-Up the Random Access Adjustment mode.

  6
• Overview 'Random Access Adjustment' mode

  6
• Selecting Setup Pattern

  6
• Internal Cross Hatch Pattern

  6
• Random access adjustment mode selection menu.

  6
• Picture Tuning

  6
• Color Balance

  6
• Sync Fast/Slow Adjustment

  6
• Peaking

  6
• Clamp Tuning

  6
• Port 2 : Video or S-Video

  6
• Line Doubler

  6
• Color Select

  6
• Focusing

  6
• Focusing color select.

  6
• Blue on source

  6
• Geometry Adjustments

  6
• Horizontal Phase Adjustment

  6
• Raster Shift Adjustment

  6
• Left-Right (east-west) Adjustments

  6
• Seagull correction

  6
• Left Side Correction

  6
• Top-Bottom (north-south) Adjustments

  6
• Seagull Correction

  6
• Horizontal Size Adjustment

  6
• Vertical Linearity Adjustment

  6
• Vertical Size Adjustment

  6
• Blanking Adjustments

  6
• Convergence Adjustment

  6
• Service mode

  7
• Starting up the Service mode.

  7
• Overview flowchart 'Service' mode.

  7
• Identification

  7
• Copy a block

  7
• Deletion of blocks

  7
• Deleting block by block

  7
• Deletion of all blocks

  7
• Change password

  7
• Change Language

  7
• Run time

  7
• Set to midposition

  7
• Undo Midposition

  7
• Convergence Mid

  7
• Undo Convergence Mid(position)

  7
• Dynamic Astigmatism (spot shape adjustment)

  7
• G2 Adjust

  7
• Gamma corrections

  7
• CRT run in cycle

  7
• Projector Warm Up

  7
• CRT Drive Mode

  7
• Messages, warnings and failures

  8
• Options

  9