Техническое РуководствоСодержаниеSwitching Module Installation1Installing Modules2Figure3-1 Catalyst 5000 Family Switch: Slot Numbers2Step1 Take the necessary precautions to prevent ESD damage.6Step2 Choose a slot for the new switching module. Check that you have enough clearance for any i...6Step3 Loosen the captive installation screws securing the switching-module filler plate (or the ...6Step4 Remove the switching-module filler plate (or the existing switching module). Save the swit...6Step5 To install the new module, hold the switching-module front panel with one hand, and place ...6Figure3-2 Installing the Module in the Catalyst 5505 Chassis7Step6 Align the edges of the switching-module carrier with the slot guides on the sides of the s...7Step7 Pivot the two module ejector levers out away from the faceplate, as shown in Figure3-2.7Step8 Carefully slide the switching module into the slot until the notches on both ejector lever...7Step9 Using the thumb and forefinger of each hand, simultaneously pivot in both ejector levers, ...7Figure3-3 Module Ejector Lever Operation8Step10 Use a screwdriver to tighten the captive installation screw on each end of the switching ...9Step11 Attach network interface cables or other devices to the interface ports.9Removing Switching Modules9Step1 Disconnect any network interface cables attached to the module ports.9Step2 Loosen the captive screws at each end of the switching module.9Step3 Place your thumbs on the left and right ejector levers. Push the levers outward to release...9Step4 Grasp the switching-module front panel with one hand, and place your other hand under the ...9Step5 Pull the switching module straight out of the slot, keeping one hand under the module to g...10Step6 Place the switching module on an antistatic mat, or in an antistatic bag, or immediately r...10Step7 If the slot is to remain empty, install a switching-module filler plate to keep dust out o...10Connecting Modules10Connecting Ethernet and Fast Ethernet Modules10Figure3-4 Group Switching Ethernet Module (10BaseT 48-Port) and Ethernet Switching Module (10Bas...11Figure3-5 Group Switching and Ethernet Switching Module Telco Cable Attachment11Connecting Ethernet Modules Using MT-RJ Connectors12Step1 Use a lint-free tissue soaked in 99 percent pure isopropyl alcohol to gently wipe the face...12Step2 Carefully wipe the faceplate with a dry lint-free tissue.12Step3 Remove any residual dust from the faceplate with compressed air before installing the cable.12Figure3-6 MT-RJ Connector13Connecting Gigabit Ethernet Modules13Figure3-7 GBIC13Table3-1 GBIC Types14Figure3-8 Installing a GBIC (WS-X5403 shown)14Figure3-9 Gigabit Ethernet Module Network Interface Connector (SC Type)15GBIC Cabling Restrictions15Connecting FDDI and CDDI Modules16Making Single-Attachment Connections16Figure3-10 Single-Attachment Station, Multimode FDDI Network Connections17Figure3-11 Single-Attachment Station, CDDI Network Connections17Making Dual-Attachment Connections18Figure3-12 FDDI Module Dual-Attachment Network Connections18Figure3-13 CDDI Module Dual-Attachment Network Connections19Installing an Optical Bypass Switch19Figure3-14 FDDI Module Optical Bypass Switch Connection19Step1 Connect the bypass switch to the ring.20Step2 Use the receive label on the cable MIC connectors as a guide, and connect the cables to th...20Step3 Connect the optical bypass switch to the FDDI module.20Step4 Connect an interface cable between the PHYA port on the station (FDDI module) side of the...20Step5 Connect an interface cable between the PHYB port on the station (FDDI module) side of the...21Step6 Connect the bypass switch control cable. If the control cable on your optical bypass switc...21Connecting ATM LANE Modules21Figure3-15 Network Interface Connector (SC Type)21Figure3-16 ATM Dual PHY Connections22Connecting ATM Dual PHY DS3 Modules22Figure3-17 ATM Dual PHY DS3 Connections23Connecting Token Ring Modules23Figure3-18 Token Ring Module Connections23Figure3-19 Fiber Token Ring Module Connections24Connecting RSMs24Connecting LightStream 1010 ATM Port Adapters24Connecting Catalyst 8510 Campus Switch Router Line Modules24Verifying and Configuring the Modules25Verifying Newly Installed Modules25Configuring the RSMs25Размер: 317,4 КБСтраницы: 26Язык: EnglishПросмотреть
