Справочник ПользователяСодержаниеQuick Start Guide1Cisco 7505 Router1Install the Hardware3Packing List3Install the Hardware4Prepare to Install the Router4Step1 Lift the router safely out of the packing container.4Step2 Ensure the power service at the site is suitable for the router you are installing.4Step3 Check the packing slip to ensure that all the proper components are present.4Step4 Confirm that you have the required tools and parts:4Install the Hardware5Rack-Mount the Router (Optional)5Step1 Measure the space between the vertical mounting strips on the rack. Confirm that the rack ...5Step2 Use the four M4 x 10-mm screws provided to attach the ears to the sides of the chassis, as...5Step3 Use the eight 10-32 x 3/8-inch screws provided to attach the ears to the mounting strips, ...5Step4 Level the chassis as required. Provide twoinches of clearance on either side of the chassis.5Install the Hardware6Install Interface Processors, Fillers, VIPs, and RSPs6Step1 Hold the interface processor, filler, VIP, or RSP with one hand, and place your other hand...6Step2 Place the interface processor, filler, VIP, or RSP in the slot and align the guide on the ...6Step3 Carefully slide the interface processor, filler, VIP, or RSP into the slot until the facep...6Step4 Use the thumb and forefinger of each hand to push the ejector levers flat against the inte...6Step5 Use a screwdriver to tighten the captive installation screws, as shown in C.6Step6 Repeat Step1 through Step5 to install the RSP or any additional interface processors, fi...6Install the Hardware7Attach the Cable-Management Brackets7Step1 Place the bracket on the rear of the chassis, as shown.7Step2 Insert three M3 x 8-mm Phillips screws, and tighten slightly with your finger.7Step3 Use a Phillips Number 1 screwdriver to tighten all three screws.7Step4 Repeat Step1 through Step3 for the second bracket.7Step5 Route the interface cables through the brackets.7Install the Hardware8Connect the Power Supply8Connect the AC-Input Power Supply8Step1 Push the cable retention clip away from the power supply receptacle, and push the power ca...8Step2 Connect the opposite end of the power cable to an appropriate power source.8Connect the DC-Input Power Supply8Step1 Turn off the power source. Locate the circuit breaker on the panel board that services the...8Install the Hardware9Step2 Loosen the two captive screws that secure the terminal block cover, as shown in A.9Step3 Pull the terminal block cover away from the terminal block, as shown in B.9Step4 Feed the return (RTN) and –48V wires through the large hole in the terminal block cover, a...9Step5 Attach a nylon cable tie to secure the cables to the terminal block cover.9Step6 Attach the RTN and –48 leads to the terminal block, as shown in C.9Step7 Attach the ground cable to the ground terminal.9Step8 Replace the terminal block cover, as shown in B.9Step9 Tighten the captive screws on the terminal block cover, as shown in A.9Connect the RSP10Connect the Console Port10Step1 Connect the console cable from the terminal to the console port on the RSP.10Step2 Check your terminal’s documentation to determine the baud rate of the terminal you will be...10Step3 Set up the terminal as follows: 9600 baud, 8 data bits, no parity, and 2 stop bits (9600, ...10Connect the Auxiliary Ports10Step1 Connect the cable from the auxiliary device to the auxiliary port on the RSP.10Step2 Check your terminal’s documentation to determine the baud rate of the terminal.10Step3 Set up the terminal as follows: 9600 baud, 8 data bits, no parity, and 2 stop bits (9600, ...10Start and Configure the System11Step1 Check the following components to make sure they are secure:11Step2 Check the console terminal to make sure it is connected to the console port and turned on.11Step3 Turn the system power switch to the on (|) position. The green AC (or DC) OK and fan OK LE...11Step4 Listen for the system blower; you should immediately hear it operating.11Step5 Observe the normal LED indicator on the RSP. If this indicator is not on after system init...11Step6 Wait until the system boot is complete before attempting to verify the status of interface...11Step7 Observe the LED indicators on the interface processors in your system. When the system boo...11Step8 Observe the system startup banner. When you start up the router for the first time, the sy...11Start and Configure the System12Start a Basic Configuration12Step1 Enter the enable command at the EXEC prompt (>), and then enter a privileged-level passwor...12Step2 Enter the configure terminal command to enter configuration mode:12Step3 Enter the config-register value configuration command, where value is a hexadecimal number...12Step4 Press Ctrl-Z to exit configuration mode.12Step5 Save the new settings to NVRAM. Enter the copy running-config startup-config command.12Step6 Enter the show version command to view the configuration register value currently in effec...12Step7 Reboot the router, and then perform a basic configuration using:12Configure Using AutoInstall12Step8 Connect to the network using a serial (WAN) cable to the channel service unit/data service...12Step9 Contact your system administrator to verify that the TCP/IP host on your network is precon...12Step10 Press Ctrl-Z to exit configuration mode.12Step11 At the # prompt, enter the copy running-config startup-config command to save the configu...12Start and Configure the System13Perform a Basic Configuration Using Setup13Step1 Select the protocols supported on your interfaces. For Internet Protocol (IP)-only install...13Step2 Enter the enable secret password and the enable password when the following is displayed:13Step3 Enter yes or no to accept or refuse SNMP management:13Step4 Enter no to refuse to enable CLNS:13Step5 Enter yes to enable routing on AppleTalk and IPX:13Step6 Enter no to refuse to enable Vines, XNS, DECnet, or bridging:13Step7 Enter yes or press Return to configure IP, and then select an interior routing protocol fo...13Step8 At the # prompt, enter the copy running-config startup-config command to save the configur...13Start and Configure the System14Configure an Ethernet Interface14Step1 To configure your system for an Ethernet LAN, respond to the prompts as follows, using you...14Step2 Enter yes to enable IPX on this interface, using the IPX network number:14Step3 Enter yes to enable AppleTalk on this interface, to configure for extended AppleTalk netwo...14Step4 At the # prompt, enter the copy running-config startup-config command to save the configur...14Configure a Synchronous Serial Interface14Step1 Enter yes to configure serial port 0:14Step2 Determine which protocols you want to allow on the synchronous serial interface and enter ...14Step3 Press Ctrl-Z to exit configuration mode.14Step4 At the # prompt, enter the copy running-config startup-config command to save the configur...14Start and Configure the System15Perform a Basic Configuration Using Configuration Mode15Step1 Enter the configure terminal command at the enable prompt to enter configuration mode from...15Step2 Enter the interface type slot/port command at the enable prompt to enter interface configu...15Step3 Press Ctrl-Z to exit configuration mode.15Step4 At the # prompt, enter the copy running-config startup-config command to save the configur...15Install Field Replaceable Units (FRUs)16Flash Memory Cards16Step1 To eject the card, press the appropriate eject button until the card is free of the connec...16Step2 Remove the card from the slot and place it in an antistatic bag to protect it.16Step3 Face the front panel of the RSP, and hold the Flash memory card with the connector end of ...16Step4 Insert the card into the appropriate slot until the card completely seats in the connector...16Install Field Replaceable Units (FRUs)17Format a Flash Memory Card17Step1 Enter format slot0: (or format slot1:) to format the Flash memory card, as follows:17Step2 At the erase all sectors prompt, press Enter to proceed.17Step3 At the volume ID prompt, enter the ID name:17Copy Files to Flash Memory17Install Field Replaceable Units (FRUs)18Make a Flash Memory Card Image Bootable18Step1 Enter the configure terminal command at the enable prompt, as follows:18Step2 Enter the no boot system command, as follows.18Step3 Enter the boot system flash slot0:new.image command, as follows:18Step4 Enter the config-register 0x2102 command to enable loading an image from Flash memory:18Step5 Press Ctrl-Z to exit configuration mode.18Step6 Enter the copy running-config startup-config command to save the configuration to NVRAM as...18Step7 Enter the reload command. When the system reloads, it will boot the image new.image from t...18Enable Booting from Flash Memory18Step1 Enter the configure terminal command at the enable prompt, as follows:18Step2 At the prompt, enter configuration commands, one per line.18Step3 Press Ctrl-Z to exit configuration.18Step4 Enter the boot system flash bootflash:slot0: filename command, as follows:18Step5 Enter the config-register command with the value shown in the following example:18Step6 Press Ctrl-Z to exit enable booting mode.18Install Field Replaceable Units (FRUs)19Prepare to Remove and Install an RSP19Install Field Replaceable Units (FRUs)20Remove and Install an Interface Processor, Filler, VIP, or RSP20Step1 Attach an ESD-preventive wrist strap between you and any unpainted chassis surface.20Step2 Disconnect all cables from the interface processor, VIP, or RSP port adapters. If you are ...20Step3 Use a screwdriver to loosen the captive installation screws, as shown in A.20Step4 Place your thumbs on both ejector levers and simultaneously pull them both outward, as sho...20Step5 Grasp the interface processor, filler, VIP, or RSP handle with one hand and pull the carri...20Step6 Store the interface processor, VIP, or RSP in an antistatic bag.20Step7 Repeat Step2 through Step6 to remove any additional interface processors, fillers, VIPs,...20Install Field Replaceable Units (FRUs)21Check the RSP Installation21Step1 Check the RSP connections to make sure they are secure:21Step2 Observe the RSP LEDs. While the system initializes, the CPU halt LED on the RSP stays on. ...21Step3 Verify that the console terminal displays the system banner and startup screen as the syst...21Step4 Verify that all the enabled LEDs (on the interface processors) are on.21Step5 When you have verified all the conditions in Step1 through Step4, the installation is co...21Install Field Replaceable Units (FRUs)22Check the Interface Processor or VIP Installation22Step1 Observe the console display messages when the system reinitializes each interface as follows:22Step2 Verify that the enabled LED on each port adapter goes on and remains on.22Step3 If the VIP is new, configure the new interfaces.22Step4 If the VIP is a replacement, use the show interfaces type slot/port adapter/port or show c...22Step5 When the interfaces are up, check the activity of each interface by observing the status L...22Install Field Replaceable Units (FRUs)23Copy the Configuration File for an RSP23Step1 Enter the enable command at the EXEC prompt (>), and then enter a privileged-level passwor...23Step2 Enter the ping command followed by the name or IP address of the remote server, and then p...23Step3 Enter the show running-config command to display the currently running configuration on th...23Step4 Create a file on the TFTP server.23Step5 Issue the copy startup-config tftp command. The EXEC command interpreter prompts you for t...23Step6 Enter the name or IP address of the remote host. In the following example, the name of the...23Install Field Replaceable Units (FRUs)24Step7 Enter the name of the configuration file. The default is to use the name of the router wit...24Step8 The system displays the instructions you entered for confirmation. If the instructions are...24Install Field Replaceable Units (FRUs)25Retrieve the Configuration File for RSPs25Step1 Enter the enable command at the EXEC prompt (>), and then enter a privileged-level passwor...25Step2 Enter the ping command followed by the name or IP address of the remote server, and then p...25Step3 Enter the copy tftp startup-config command and press Return to enter the configuration mod...25Step4 Enter the IP address or name of the remote host (the remote TFTP server to which you origi...25Step5 Enter the name of the configuration file. The default is to use the name of the router wit...25Step6 Before the system reloads the new configuration file in NVRAM, it displays the instruction...25Install Field Replaceable Units (FRUs)26Step7 Enter the show startup-config command to confirm that the configuration file was retrieved...26Step8 To ensure that the startup configuration file stored in NVRAM is the default running confi...26Install Field Replaceable Units (FRUs)27Remove and Install Port Adapters27Step1 Remove the screw that secures the port adapter (or blank port adapter), as shown in A.27Step2 Grasp the handle and carefully pull it out of its slot, away from the edge connector at th...27Step3 To insert the port adapter, align the carrier between the upper and the lower edges of the...27Step4 Carefully slide the port adapter into the slot until the connector is completely seated in...27Step5 Install the screw in the rear of the port adapter slot on the VIP. Do not overtighten the ...27Step6 Carefully slide the VIP motherboard into the interface processor slot until the connectors...27Install Field Replaceable Units (FRUs)28Remove the Power Supply28Step1 Turn off the system power switch.28Step2 Disconnect the power cable from the power supply.28Step3 Attach an ESD-preventive strap between you and any unpainted chassis surface.28Step4 Disconnect the power harness plug from the backplane receptacle by pulling the polarized p...28Step5 Use a Number 2 Phillips screwdriver to remove the two M4 x 10-mm Phillips panhead screws t...28Step6 Using both hands, grasp both of the power supply handles and pull the power supply about h...28Install Field Replaceable Units (FRUs)29Replace the Power Supply29Step1 Hold the power supply as shown in C, and slide it into the bottom of the chassis. Use the ...29Step2 Use a Number 2 Phillips screwdriver to replace the two M4 x 10-mm Phillips panhead screws ...29Step3 Reattach the power harness plug to the backplane receptacle. Ensure that the plug is fully...29Step4 Replace the power harness cover.29Step5 Replace the fan tray.29Step6 Replace the cover panel.29Step7 For AC-input power supplies: On the interface processor side of the power supply, replace ...29Размер: 543,4 КБСтраницы: 32Язык: EnglishПросмотреть
