Справочник ПользователяСодержаниеt6y1t6y1RFK5501/5500-433 v1.11Installation Instructions, Instrucciones de instalación1Installation Instructions, Instrucciones de instalación1English, Español1English, Español2English, Español2English2Installation Instructions2Installation Instructions2•PC5802•PC5852•PC1555MX2•PC15652•PC16162•PC18322•PC18642•PC50052•PC50082•PC50102•PC50152•PC50162•PC50202•PC50202•PC50202•PC50202•One Power keypad2•Keypad inner door labels2•Four mounting screws2•1 tamper switch2•2 end-of-line resistors2•Installation Instructions21. Insert a flat head screwdriver into the provided slot (first of two)22. Move screwdriver toward the back plastic and lift as in the below diagram. This will unhook one side of the front plastic.23. Repeat step # 1 and 2 on the second provided slot to disconnect the front plastic and allow access for wiring.21. Secure Keypad to wall using mounting holes. Use all 4 screws provided unless mounting on a single gang box.22. Place keypad into hooks on the backplate and swing down to engage.23. Run wire through wiring slot or knockouts. Connect Keybus and PGM/Zone wiring to keypad. Place tamper switch into tamper hole on backplate.24. Remove keypad from hooks. Place keypad into backplate, ensure the wire is pushed back into the wall as much as possible. Route the wire inside the keypad ensuring high components are avoided. Snap the front assembly closed, ensuring that there is ...21. Before wiring the unit, ensure that all power (AC transformer and battery) is disconnected from the control panel.22. Connect the four Keybus wires from the control panel (red, black, yellow and green) to the keypad terminals. Refer to diagram:23. If programmed as an input, you can connect a device - such as a door contact - to the ‘P/Z’ terminal of the keypad. This eliminates the need to run wires back to the control panel for the device. To connect the zone, run one wire from the devi...24. If the ‘P/Z’ terminal is programmed as an output, the output follows the PGM programmed in Section [080]. A small relay, buzzer or other DC operated device may be connected between the positive supply voltage and the ‘P/Z’ terminal (maximu...21. Connect the battery leads to the battery.32. Connect the AC transformer.31. Enter Installer Programming by pressing [Q][8][Installer’s Code]32. Press [000] for Keypad Programming33. Press [0] for Partition and Slot Assignment34. Enter the 1st digit (0 to 8 for partition assignment)35. Enter the 2nd digit (1 to 8 for slot assignment supervision)36. Press the [#] key twice to exit programming.37. After assigning all keypads, perform a supervisory reset by entering [Q][8][Installer’s Code][902] and wait for 60 seconds.38. Press the [#] key to exit programming after 60 seconds.31. Enter keypad programming by pressing [Q][8][Installer Code][Q]. Enter the 3-digit section number for the label to be programmed.32. Use the arrow keys (<>) to move the underline bar underneath the letter to be changed.33. Press the number keys [1] to [9] corresponding to the letter you require. The first time you press the number the first letter will appear. Pressing the number key again will display the next letter.3[1] - A, B, C, 13[4] - J, K, L, 43[7] - S, T, U, 73[0] - Space3[2] - D, E, F, 23[5] - M, N, O, 53[8] - V, W, X, 83[8] - V, W, X, 83[3] - G, H, I, 33[6] - P, Q, R, 63[9] - Y, Z, 9,03[9] - Y, Z, 9,034. When the required letter or number is displayed use the arrow keys (<>) to scroll to the next letter.35. When you are finished programming the Zone Label, press the [Q] key, scroll to “Save,” then press [Q].36. Continue from Step 2 until all Labels are programmed.31. Press [Q][6][Master code].32. Use the [<][>] keys to scroll to either Brightness Control or Contrast Control.33. Press [Q] to select the setting you want to adjust.34. a) ‘Brightness Control’: There are multiple backlighting levels. Use the [<][>] keys to scroll to the desired level. b) ‘Contrast Control’: There are 10 different display contrast levels. Use the [<][>] keys to scroll to the desired contra...35. To exit, press [#].31. Press [Q][6][Master Code].32. Use the [>] key to move through the 4 different backlighting levels.33. The level is automatically saved when you press [#] to exit.31. Press [Q][6][Master Code].32. Use the [<][>] keys to scroll to Buzzer Control.33. There are 21 different levels, use the [<][>] keys to scroll to the desired level.34. To exit, press [#].31. Press [Q][6][Master Code].32. Use the [<] key to move through the 21 different buzzer levels.33. The level is automatically saved when you press [#] to exit.3Partition Assignment (0=Global Keypad)5Slot Assignment51 to 85[1]5Function Key 1 Assignment500 to 325Stay Arm5[2]5Function Key 2 Assignment500 to 325Away Arm5[3]5Function Key 3 Assignment500 to 325Chime On/Off5[4]5Function Key 4 Assignment500 to 325Sensor Reset5[5]5Function Key 5 Assignment500 to 325Quick Exit5[00] - Null5[08] - Bypass Mode5[16] - Quick Exit5[26] - Time & Date Program5[01] - Partition 1 Select5[09] - Trouble Display5[17] - Activate Stay/Away5[27] - Partition 3 Select5[02] - Partition 2 Select5[10] - Alarm Memory5[18] - *Global Away Arm5[28] - Partition 4 Select5[03] - Stay Arm5[11] - User Programming5[19] - Command Output 35[29] - Partition 5 Select5[04] - Away Arm5[12] - User Functions5[21] - Command Output 45[30] - Partition 6 Select5[05] - No Entry Arm5[13] - Command Output 15[22] - *Global Disarming5[31] - Partition 7 Select5[06] - Chime On/Off5[14] - Command Output 25[23] - Bypass Recall5[32] - Partition 8 Select5[07] - System Test5[15] - *Global Stay Arm5[24] - Bypass Group Recall5[33] - Local PGM Activate5*Available only on the PC1616/PC1832/PC1864 version 4.2 or higher.5[001] to [064]51 to 645[101] to [108]61 to 86[00] - Null8[07] - System Test8[17] - Activate Stay/Away8[27] - Disarm8[03] - Stay Arm8[13] - Command Output 18[18] - Global Away Arm8[28] - Fire Alarm8[04] - Away Arm8[14] - Command Output 28[19] - Command Output 38[29] - Auxiliary Alarm8[05] - No Entry Arm8[15] - Global Stay Arm8[21] - Command Output 48[30] - Panic Alarm8[06] - Chime On/Off8[16] - Quick Exit8[22] - Global Disarm8[31] - Local PGM Activate8©2009 Digital Security Controls, Toronto, Canada • www.dsc.com4Размер: 2,1 МБСтраницы: 16Языки: English, EspañolПросмотреть
