Инструкции для National Instruments GPIB-ENET/100

Содержание

• Getting Started with Your GPIB-ENET/100 and NI-488.2™ for Mac OS

  1
• Support

  2
  • Worldwide Technical Support and Product Information

    2
  • National Instruments Corporate Headquarters

    2
  • Worldwide Offices

    2
• Important Information

  3
  • Warranty

    3
  • Copyright

    3
  • Trademarks

    3
  • WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS

    3
• Compliance

  4
• Contents

  6
• About This Manual

  9
  • Conventions

    9
  • Related Documentation

    10
• Chapter 1 Introduction

  11
  • What You Need to Get Started

    11
  • Optional Equipment

    12
    • Optional Hardware

      12
    • Multiple-Computer Software License

      12
  • GPIB-ENET/100 Hardware Overview

    12
    • Feature Overview

      13
    • LED Overview

      13
  • NI-488.2 Overview

    14
  • Time-Saving Development Tools

    15
• Chapter 2 Installation

  16
  • Installing NI-488.2

    16
  • Installing the GPIB-ENET/100 Hardware

    17
    • Step1. Record the Serial Number, Ethernet Address, andDefaultHostname

      17
    • Step2. Connect the Cables

      18
    • Step3. Switch on Your GPIB-ENET/100

      19
• Chapter 3 Ethernet Configuration

  21
  • Entering Network Configuration Mode

    21
  • Using the NI Ethernet Device Configuration Utility

    22
    • Changing the Network Settings

      24
    • Static IP Parameters

      26
    • Choosing a Static IP Address

      26
      • For a Network Administered by a Network Administrator

        26
      • For a Network without a Network Administrator

        27
    • Verifying the Hostname

      28
• Chapter 4 GPIB Configuration

  30
  • Configuring the NI-488.2 Software Characteristics

    30
    • Changing the Software Settings

      30
    • Restart Your Computer

      32
• Chapter 5 Verify the Installation

  33
  • Verifying the Software Installation

    33
  • Connecting the GPIB Cable

    34
• Chapter 6 Using Your GPIB-ENET/100 and NI-488.2

  35
  • Using DHCP

    35
  • Using the CFG RESET Switch

    36
    • Using the CFG RESET Switch during Operation

      37
    • Using the CFG RESET Switch at Power-On

      38
  • Updating the Firmware

    38
  • Using the IBIC 488.2 Utility

    40
  • Programming Considerations

    40
• Appendix A PWR/RDY LED Signaling

  41
• Appendix B Troubleshooting and Common Questions

  43
• Appendix C Specifications

  48
• Appendix D Technical Support Resources

  50
• Glossary

  52
  • Symbols

    52
  • A-C

    52
  • D-L

    53
  • M-V

    54
• Index

  55
  • A-D

    55
  • E-H

    56
  • I-N

    57
  • O-R

    58
  • S-W

    59
• Figures

  8
  • Figure 1-1. GPIB-ENET/100 Front Panel

    13
  • Figure 2-1. GPIB-ENET/100 Baseplate Identification Label

    17
  • Figure 2-2. GPIB-ENET/100 Rear Panel

    18
  • Figure 2-3. Connecting Power to the GPIB-ENET/100

    19
  • Figure 3-1. NI Ethernet Device Configuration Utility

    22
  • Figure 3-2. Properties Display for an Unconfigured GPIB-ENET/100

    24
  • Figure 3-3. Specifying IP Settings

    25
  • Figure 3-4. Hostname Verification Error Detected

    28
  • Figure 4-1. Ethernet Settings in NI-488 Config

    31
  • Figure 6-1. NI Ethernet Device Firmware Update Utility

    39
• Tables

  8
  • Table 1-1. LED Descriptions

    14
  • Table 3-1. Valid and Invalid IP Addresses for Subnet Mask 255.255.255.0

    27