Справочник ПользователяСодержаниеAbout this document9Subject9Applicable systems10Intended audience11Conventions11Related information11Preparing for installation13Contents13Preparing the site13Unpacking and inspecting14Taking inventory14Installing ISDN BRI hardware15Contents15Installing ISDN BRI hardware for line applications15Installing ISDN BRI hardware for trunk applications38Preparing the system47Contents47Introduction47Verifying ISDN BRI operation47Setting up ISDN BRI test terminals and trunks48Configuring ISDN BRI hardware53Contents53Hardware requirements53Configuring ISDN BRI trunking with IP expansion cabinets or MG 1000S systems55Installation procedures56Testing ISDN BRI functions87Contents87Introduction87Voice calls88Circuit-switched data calls99Packet data transmission100Testing an ISDN BRI trunk103Removing the test setup103Generating traffic reports105Contents105Introduction105Figures18Figure 1 NT8D35 Network module (Large System)18Figure 2 NT8D37 IPE module (Large System)19Figure 3 NT4N41 Core/Network module (Large System)19Figure 4 Module cover locking latches20Figure 5 Connect the ISDN BRI terminals to the Large System24Figure 6 Connect the system to the MDF26Figure 7 Cross-connect the SILC port to the office wiring31Figure 8 Cross-connect the UILC port to the office wiring32Figure 9 Connect the ISDN BRI terminal to the S/T interface37Figure 10 Connect the ISDN BRI network termination (NT1) to the U interface38Figure 11 Clock reference cable connection41Figure 12 Connect the network termination to the U interface and to the S/T interface (in TE mode)43Figure 13 ISDN BRI acceptance testing setup for terminals49Figure 14 ISDN BRI acceptance testing setup for trunking - Local Exchange connectivity50Figure 15 ISDN BRI acceptance testing setup for trunking - TIE trunk connectivity51Figure 16 SILC line power options62Figure 17 Jumper plug settings for normal power on the TX and RX leads63Figure 18 Jumper plug settings for reverse power on the TX and RX leads63Figure 19 Connecting ISDN BRI terminals to the system66Figure 20 Cable connectors in main cabinet68Figure 21 Cable connectors in the expansion cabinet68Figure 22 Cable connectors in the second expansion cabinet69Figure 23 Back of MG 1000S cable connectors69Figure 24 SILC port designation label at the cross-connect terminal69Figure 25 UILC port designation label at the cross-connect terminal70Figure 26 Cross-connecting a SILC port to the office wiring73Figure 27 Cross-connecting a UILC port to the office wiring74Figure 28 Connecting the ISDN BRI terminal to the S/T interface78Figure 29 Connecting the ISDN network terminator to the U interface79Figure 30 Cross-connecting an SILC port84Figure 31 Cross-connecting a UILC port85Figure 32 Connecting the ISDN network terminator to the U interface and to the S/T interface (in TE mode)86Figure 33 Network traffic report106Tables10Table 1 Meridian 1 systems to CS 1000M systems10Table 2 ISDN BRI card location16Table 3 SILC port designations at the MDF: NT8D37 IPE module (16-cable configuration)27Table 4 UILC port designation labels at the MDF: NT8D37 IPE module (16-cable configuration)27Table 5 NT8D37 IPE moduleSILC and UILC pair-terminations for connectors A, E, K, R (12-cable configuration)33Table 6 NT8D37 IPE moduleSILC and UILC pair-terminations for connectors B, F, L, S (12-cable configuration)33Table 7 NT8D37 IPE moduleSILC and UILC pair-terminations for connectors C, G, M, T (12-cable configuration)34Table 8 ISDN BRI clock reference tables40Table 9 Clocks as differential pairs42Table 10 Card location form: NT8D37 IPE module (16-cable configuration)44Table 11 Card location form: NT8D37 IPE module (12-cable configuration)44Table 12 Hardware requirements for line and packet data applications53Table 13 Hardware requirements for ISDN BRI trunking55Table 14 Correct responses to LOOP and MISP prompts in LD 2756Table 15 Small System shelf slot assignments for ISDN BRI cards58Table 16 SILC and UILC port assignments connectors at cross-connect terminal71Table 17 S/T interface connector specification75Table 18 U interface connector specification76Table 19 M5317TDX terminal error codes81Procedures16Procedure 1 Selecting the card slots16Procedure 2 Remove the module cover for card installation20Procedure 3 Installing the MISP21Procedure 4 Removing the MISP21Procedure 5 Installing the BRSC, SILC, and UILC22Procedure 6 Remove the BRSC, SILC, and UILC23Procedure 7 Connecting ISDN BRI terminals to the system23Procedure 8 Connect the modules to the MDF24Procedure 9 Cross-connecting SILC and/or UILC ports to the building wiring29Procedure 10 Connecting the ISDN BRI terminals to the DSL36Procedure 11 Providing clock referencing on the SILC39Procedure 12 Connecting clock reference cables41Procedure 13 Performing acceptance testing48Procedure 14 Selecting the card slots58Procedure 15 Installing the MISP59Procedure 16 Removing the MISP60Procedure 17 Installing the SILCs and UILCs61Procedure 18 Removing the SILC and UILC64Procedure 19 Installing the PRI hardware64Procedure 20 Connecting system cables to the cross-connect terminal66Procedure 21 Cross-connecting the DSLs at the cross-connect terminal70Procedure 22 Connecting the terminating resistor to the SILC DSL74Procedure 23 Connecting the ISDN BRI terminals to the DSL76Procedure 24 Initializing a Nortel Networks M5317TDX terminal80Procedure 25 Connecting the system cables to the cross-connect terminal82Procedure 26 Cross-connecting DSLs at the cross-connect terminal83Procedure 27 Performing a call hold test88Procedure 28 Perform a Call Waiting test89Procedure 29 Performing a Call Forward No Answer test91Procedure 30 Perform a Calling Line Identification Presentation test92Procedure 31 Perform an ISDN BRI Conference test93Procedure 32 Perform a Call Join test on Conference94Procedure 33 Perform a hunting test96Procedure 34 Perform an ISDN BRI NI-1 Call Forward All Calls test97Procedure 35 Perform an ISDN BRI ETSI Call Forwarding Unconditional test98Procedure 36 Perform a circuit-switched data call test99Procedure 37 Perform a B-channel packet data transmission test using an external packet handler100Procedure 38 Perform a D-channel packet data transmission test using an external packet handler101Procedure 39 Perform a D-channel Switched Virtual Circuit packet data transmission test using an MPH101Procedure 40 Perform a B-channel Switched Virtual Circuit packet data transmission test using an MPH102Procedure 41 Perform procedure to test an ISDN BRI trunk DSL103Размер: 3,1 МБСтраницы: 108Язык: EnglishПросмотреть
