Инструкции для RTS SSA-424A

Содержание

• General Description

  5
• Features

  5
  • FIGURE 1. SSA-424A Reference View

    6
• Front and Back Panel Descriptions

  6
  • Front Panel

    6
  • Back Panel

    6
• Specifications

  7
• Mounting

  9
• 4-Wire Audio Connections

  9
  • ADAM, ADAM-CS, or Zeus Audio Connection

    9
    • 1. Use standard 9-pin or RJ-11 keypanel cables. Connect from one port of your intercom system to J2A or J3A (System A connection) on the back of the SSA-424A. Connect from another port to J2B or J3B (System B connection).

      9
    • 2. On the SSA-424A front panel, set the 4W LEVEL REF SEL switches to the +8 dB position.

      9
  • Audio Connections for the Other 4-wire Communications Systems

    9
    • 1. Construct 9-pin or RJ-11 cables to connect from the 4-wire system to the SSA-424A. To connect to the System A hybrid, use either J2A or J3A; for the System B hybrid, use either J2B or J3B. Pin connections are as follows:

      9
    • 2. On the SSA-424A front panel, set the 4W LEVEL REF SEL switches to the position which most closely matches the audio input and output levels of your 4-wire system. If you don’t know the levels, select the +8 dB position for now.

      10
      • FIGURE 2. Rack Mount Configurations

        10
• 2-Wire Audio Connections

  10
  • RTS TW Audio Connections

    10
    • 1. Use standard TW intercom cables. Standard TW system cables can carry either one or two channels, while each hybrid in the SSA...

      10
    • 2. On the SSA-424A front panel: For System A and System B, set the 2W CHAN SEL switch to the appropriate position. To interface to TW channel 1 select position 1; for TW channel 2, select position 2.

      11
      • FIGURE 3. Using a TW-5W to connect to two TW channels to the SSA-424A

        11
  • Audiocom Audio Connection

    11
    • 1. You can directly connect standard Audio 1-channel cables. Connect one Audiocom channel to the J1A connector on the back of th...

      11
    • 2. On the SSA-424A front panel, set the 2W CHAN SEL switches for System A or System B to the BAL position.

      11
      • FIGURE 4. Using a JB-2 Junction Box to split a 2-channel Audiocom cable into two 1-channel cables.

        11
  • Clear-Com Audio Connection

    11
    • 1. Use standard Clear-Com 3-pin cables. Connect one Clear-Com party line to the J1A connector on the back of the SSA-424A (System A). Connect a separate Clear- Com party line to the J1B connector (System B).

      11
    • 2. On the SSA-424A front panel, set the System A and System B 2W CHAN SEL switches to position 2.

      11
  • Other 2-wire Audio Connection

    11
    • 1. Use the J1A connector on the back of the SSA-424A to connect one 2-wire line to the System A hybrid. Use the J1B connector to...

      11
    • 2. On the SSA-424A front panel, set the CHAN SEL switches as follows:

      12
• 4-Wire Call Signal Connections

  12
  • Call Signal Connection for ADAM, ADAM CS, and Zeus

    12
    • FIGURE 5. Call signal connections for ADAM, ADAM CS, and Zeus Intercom Systems. This example uses GPI outputs #1 and #2 and GPI ...

      13
    • TABLE 1. GPI Connector Pin-out (ADAM, ADAM CS, and Zeus)

      13
    • TABLE 2. UIO-256 GPI Input Connector (J7)

      14
    • TABLE 3. UIO-256 GPI Outputs Connector (J5)

      14
  • Call Signal Connections for other 4-wire Communications Systems

    15
    • FIGURE 6. Typical call send and call enable/inhibit connections for a 4-wire intercom system.

      15
    • FIGURE 7. Call signal connections for a 4-wire intercom system other than ADAM, ADAM CS and Zeus.

      16
• 2-Wire Call Signal

  16
  • Call Signal Connections for Audiocom, RTS TW and Clear-Com

    16
  • Call Signal Connections for Other 2-Wire Communication Systems

    16
• General Instructions

  17
  • 1. Attach the power pack to the SSA-424A and apply power to all components. Confirm the power indicator is lit on the SSA-424A front panel.

    17
  • 2. Use the level adjust trimmers (Figure 8) to fine tune the listen levels.

    17
    • FIGURE 8. Location of level adjust trimmers

      17
• Operating Notes for ADAM, ADAM CS and Zeus Intercom Systems

  17
  • 1. In AZedit use port alpha setup to name each 4-wire intercom port that is connected to the SSA-424A. Choose names which help indicate which 2-wire line is being interfaced.

    17
  • 2. Key assignment, party line assignment, etc. is the same as for any other intercom port.

    17
  • 3. Optional call signal output using the GPI: you can assign the GPI output to a talk or listen key, then activate that key to generate a call signal.

    17
  • 4. Optional call signal input using the GPI

    18
  • 5. Optional call enable control. If you connected a GPI Output for use as a call enable control, you can assign that GPI output ...

    18
  • 6. Send your changes to the intercom system. This completes any required programming for ADAM, ADAM CS, or Zeus intercom system.

    18
• Internal Access

  19
  • 1. Remove six screws from the back cover.

    19
  • 2. Remove the top cover. This provides access to all internal adjustments.

    19
  • 3. For option card installation, slide the circuit board out toward the back to remove it from the bottom cover.

    19
    • FIGURE 1. Location of screws for disassembly.

      19
    • FIGURE 2. Locations of internal controls

      19
• Mode Dip Switch Settings

  19
  • TABLE 1. Mode DIP Switch Settings

    19
• Call Signal Option Card Installation

  20
  • 1. Disassemble the SSA-424A as previously described.

    20
  • 2. Assemble the standoffs to the circuit board using the supplied screws and lock-washers.

    20
  • 3. Connect the supplied power cable from J8 on the option card to J303 on the main board of the SSA-424A.

    20
  • 4. Insert the connectors on the option card into the connectors on the main board.

    20
  • 5. Use the remaining screws and lock-washers to secure the standoffs to the main board.

    20
  • 6. Reassemble the SSA-424A.

    20
    • FIGURE 3. The Call Signal Option Card after installation in the SSA-424A.

      20