Справочник ПользователяСодержаниеIntroduction4Description4Features4Installation6Unpacking6Configuration Pre-check6DIP Switches6Power-Up14Sidetone Adjustment14Operation15Channel Select (SS-2002 & SS-2002RM Only)15Headset/Headphone/Speaker/Microphone Selection15Receiving Calls15Calling an Intercom Channel15Specifications16General16Dynamic-mic Headset/Handset16Panel Microphone16Intercom Channels, Balanced mode (SW1 set to BAL position)16Intercom Channels, Unbalanced mode (SW1 set to UNBAL position)16Speaker Output Power17Dimensions17Размер: 1,1 МБСтраницы: 18Язык: EnglishПросмотреть
Справочник ПользователяСодержаниеModel SS-1002 Single-Channel Intercom Speaker Station1Models SS-2002 Two-Channel Intercom Speaker Station1Model SS-2002 RM Two-Channel Rack Mount Intercom Speaker Station1Technical Manual1Introduction5Description5Features61. Channel and Power Connections -62. Configuration DIP Switches -63. Panel Mic Key -64. Speaker Key -65. Channel Select Key (SS-2002 & SS-2002RM only) -66. Volume Control -67. Intercom Listen Key -68. Call Key -69. Intercom Talk Key -610. Dynamic-Mic Headset Connector -611. Panel Mic Connector -612. Built-in Panel Microphone -613. Sidetone Trimmers -714. Balanced/Unbalanced Selector Switch -7FIGURE 1. SS-1002/2002 Features7FIGURE 2. SS-2002RM Features8Configuration Pre-check91. Remove the four (4) screws on the front panel that secure the intercom station faceplate to the mounting box.92. Pull the faceplate out for all versions (except the RM version).91. Remove the 10 screws securing the cover on the box.92. Lift the cover off.9DIP Switches9TABLE 1. DIP Switch descriptions and factory default settings9Mic Kill Receive10> Set DIP switch 1 to the open position.10> Set DIP switch 1 to the closed position.10Call Signal Compatibility101. Verify Dip Switch 2 is in the OPEN position.102. Verify the Balanced/Unbalanced switch is in the Balanced position.101. Set DIP switch 2 to the CLOSED position.102. Set the Balanced/Unbalanced switch to the Unbalanced position.10Incoming Call Beep10> Set DIP switch 3 to the OPEN position (default). DIP switch 3 must also be in the OPEN position if you want to activate incoming call beep to the speaker using DIP switch 5.10Microphone Type10> Set DIP switch 4 in the open (default) position.10> Set this switch to the closed position.10Speaker Beep for Incoming Call11> Set DIP switch 5 to the closed position if you want to hear incoming call beep in the speaker.11Balanced/Unbalanced Switch11Sidetone Trimmers11FIGURE 3. DIP Switch location RM version (left), SIP switch location S, U, and P Versions (right).11Headset Connector Notes11Panel Mic Connector Notes111. Insert the 1/4” RTS connector into the panel microphone connector.112. Screw the microphone in.11Intercom Channel Connections12Description of Phantom-Powered Connection12FIGURE 4. Phantom Powered Example12Description of Locally Powered Connection13FIGURE 5. A 2-channel Audiocom intercom system using a PS2001L power supply.13All Locally Powered Intercom Stations (Dry Lines)14FIGURE 6. Intercom system using all locally powered U box stations.14FIGURE 7. Audiocom mode line termination for dry-line operation. (One required for each channel). The termination is available via P/N 9020-7550-000.14FIGURE 8. Audiocom mode connections for an SS-1002 Intercom Station in a U box. For Clear-Com connection, use the Unbalanced Mode Intercom Channel pin out information listed in “Specifications” on page 18.15FIGURE 9. Audiocom mode connections for an SS-2002 Intercom Station in a U box. For Clear-Com connection, use the Unbalanced Mode Intercom Channel pin out information listed in “Specifications” on page 18.15FIGURE 10. Audiocom cable wiring diagrams16Power Up171. Verify the local power supplies are plugged in.172. Turn on the power switches of any phantom power supplies (PS-2001L, SPS-2001, etc.).17Sidetone Adjustment171. Activate channel 1 as described in “Channel Select (SS-2002 & SS-2002RM Only)” on page 16.172. Activate talk and listen as described in the operating instructions.173. Slowly increase the volume to maximum while talking into the microphone.174. Using a small, flat-head screwdriver, adjust the channel 1 sidetone trimmer to minimize your voice level in the headphones.175. Activate channel 2.176. Repeat the steps 1 through 5 to adjust the channel 2 sidetone.177. Install the intercom station mounting screws after completing the adjustments. The stations is now ready for use.171. Activate channel 1.182. Activate talk and listen.183. Set the volume control to the normal listening level for intercom audio.184. While talking into the microphone, use a small, flat-head screwdriver to adjust the channel 1 sidetone trimmer so you can hear your own voice in the headphones at an acceptable level.185. Activate channel 2.186. Repeat the steps 1 - 5 to adjust the channel 2 sidetone.18Channel Select (SS-2002 & SS-2002RM Only)18> Tap the Ch Select key to select channel 1 or 2. The key is green when channel 1 is selected and red when channel 2 is selected.18Headset/Headphone/Speaker/Microphone Selection18Receiving Calls181. Turn ON the listen keys and begin your conversation.192. Turn the keys OFF when finished.19Calling an Intercom Channel191. Select the desired intercom channel.192. Press and hold the Call key. An inaudible call signal is sent, and the Listen key automatically turns ON.193. When you hear a response, release the Call key and activate the Talk key.194. Turn OFF the Listen key to end the conversation.19Specifications20Dimensions21FIGURE 11. Dimensions21Installing the Box to the Faceplate23General Instructions23Step 123TABLE 2. SS1002 wire connections for use in Audiocom System23TABLE 3. SS1002 wire connections for use in Clear-com System23TABLE 4. SS2002 Wire Connection for use in Audiocom System24TABLE 5. SS2002 Wire Connections for use in Clear-com System24Step 224Step 324Notes25Размер: 1,1 МБСтраницы: 26Язык: EnglishПросмотреть
