Инструкции для UTC Fire & Security Americas Corporation Inc 723-TCVR

Содержание

• Product Summary

  1
  • SuperBus 2000 vs. SuperBus

    1
  • The SuperBus 2000 RF Receiver Module features:

    1
    • Figure 1. RF Receiver Module Components

      1
    • Table 1. Component Descriptions

      1
• Component

  1
• Function

  1
  • Installation Guidelines

    2
    • Table 2. Maximum Module Wire Lengths

      2
• Wire Gauge (Unshielded or Shielded)

  2
• Max. Wire Length Between Module and Concord Panel

  2
  • Figure 2. Mounting on or Near Metal

    2
  • Tools and Supplies

    2
  • Installation

    2
    • Figure 3. Removing the Cover

      2
    • To mount the module on a wall:

      2
      • 1. Remove the panel AC power transformer and disconnect the backup battery.

        2
      • 2. Remove the module cover and set it aside (Figure 3).

        2
      • 3. Hold the base against the mounting surface and mark the three mounting holes (Figure 1). Remem...

        2
      • 4. Drill holes and insert the appropriate anchors.

        2
      • 5. Secure the back-plate to the wall with included panhead screws.

        2
    • To mount the module in a Concord panel cabinet:

      2
      • 1. Remove the panel AC power transformer and disconnect the backup battery.

        2
      • 2. Remove and discard the module cover (Figure 3).

        2
      • 3. Insert a support standoff shown in Figure 4 (supplied with panel) into the panel circuit board...

        3
        • Figure 4. Support Standoff

          3
      • 4. Slide the module back-plate into the two top mounting clips located on the top-right side of t...

        3
        • Figure 5. Mounting the module in a Concord Cabinet

          3
      • 5. Push the lower-left corner of the module onto the support standoff (see detail in Figure 5).

        3
    • Connecting the Antennas to the Module

      3
      • 1. Loosen the inside terminals of the left and right antenna terminal blocks (see Figure 1).

        3
      • 2. Insert an antenna into each inside terminal. (Insert antennas through cabinet top holes when m...

        3
      • 3. Tighten the antenna terminal screws.

        3
  • Concord Panel Wiring

    3
    • To wire the receiver module to Concord panels:

      3
      • 1. Disconnect the panel power transformer and backup battery.

        3
      • 2. Wire the module to the panel power and bus terminals as shown in Figure 6.

        3
        • Figure 6. Wiring the Receiver Module to Concord Hardwire and Wireless Panels

          3
  • Installing an Optional Cover Tamper Switch

    3
    • To install the tamper reed switch (Figure 7):

      3
      • 1. Slide the reed switch into the reed switch holder located on the module back-plate as shown in...

        3
      • 2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...

        4
      • 3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the desire...

        4
        • Figure 7. Installing the Optional Reed Switch

          4
  • Setting the Unit Number

    4
    • Setting the Unit Number on Concord Panels with Software Versions 1.0–1.6

      4
      • Figure 8. Unit Number DIP Switch Settings

        4
    • Setting the Unit Number on Concord Panels with Software Version 2.0 or Later

      4
  • Power Up and Bus Communication

    4
    • To power up the panel and receiver module:

      4
      • 1. Verify that all wiring at the panel, touchpad, and receiver is correct.

        4
      • 2. Connect the panel backup battery and plug in the panel AC power transformer.

        4
      • 3. Verify that the receiver module status LED is on.

        4
      • 4. If desired, enter panel program mode to verify unit number exists (see panel Installation Inst...

        4
    • Changing the Receiver Module Unit Number (software versions 1.0–1.6)

      5
    • To change the receiver module unit number:

      5
      • 1. Remove panel AC power transformer and backup battery.

        5
      • 2. Change the DIP switch setting on the module (see Figure 8). Remember, the setting must be diff...

        5
      • 3. Connect the panel backup battery and plug in the AC power transformer. The panel automatically...

        5
      • 4. The system may still indicate a bus failure if the panel learned a unit number that is no long...

        5
      • 5. Exit from program mode. The touchpad and all other bus devices should operate correctly and an...

        5
    • Replace Module Cover/Close Cabinet

      5
  • Programming

    5
  • Testing

    5
  • Troubleshooting

    5
    • Table 3. Troubleshooting

      5
• Problem

  5
• Action/Solution

  5
  • 1. Check for incorrect wiring connections.

    5
  • 2. Make sure the panel AC power transformer is plugged in and the backup battery is connected.

    5
  • 3. If the LED still remains off, replace the module.

    5
  • 1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...

    5
  • 2. Check for incorrect wiring connections.

    5
  • 3. Check receiver antenna connections.

    5
  • 4. Check for receiver antenna proximity to metal obstructions such as ducting or AC wiring.

    5
  • 5. If the LED still doesn’t flash, replace the module.

    5
  • 1. Check that no bus devices are set to the same unit number.

    5
  • 2. Change the module unit number and re-initialize the panel/module by disconnecting and reconnec...

    5
  • 1. Make sure that the wireless zone capabilities of the module and panel have not been exceeded. ...

    5
  • 2. If the system still doesn’t respond, replace the module.

    5
  • Specifications

    6
  • Notices

    6