Справочник ПользователяСодержаниеViVOpay 4500™ Overview 14Troubleshooting 134Glossary 144Customer Support 164ViVOpay 4500™ Overview5Overview5Features5Additional Features5ViVOpay 4500 Specifications6Installing ViVOpay 45007ViVOpay 4500 Counter Top Stand7Bracket and Saddle Installation71. Assemble the ViVOpay 4500 counter top stand by inserting the saddle into the base. Make sure to align the curved part of the saddle with the curved part of the base.72. Attach the base to the countertop using the three screws that come with the counter top stand.73. Slide the bottom of the ViVOpay 4500 down into the saddle. Press the sides firmly until the tabs snap into place.74. Attach the serial cable from the ViVOpas 4500 to the appropriate POS.75. Insert the ViVOpay power cable into the power module.76. Plug the power adapter into the power outlet.77. Peel the clear protective sheeting from the surface of each overlay.78. Install the required driver from the supplied software disc if you are attaching the ViVOpay 4500 to a computer using the 3750 DONGLE (Part Number 220-1273-00).7Ingenico enTouche 10008Bracket and Saddle Installation81. Disconnect the power adapter from the Ingenico unit.82. Turn the Ingenico unit so that the bottom is facing up.83. Grasp the rear cover, gently apply pressure the top, and pull it up and away from the unit.84. Insert the male ViVOpay 4500 plug into the female Ingenico plug on the bottom right side.95. Insert the female plug into the POS jack.96. Slide the saddle shown below into the prongs on the new Ingencio cover.97. Replace the original Ingenico cover with the ViVOpay 4500 cover by inserting the bottom two prongs of the saddle into the applicable slots on the bracket and snap the top into place.98. Fit or gather the cables under the cover. The resulting configuration is shown below.99. Slide the bottom half of the ViVOpay 4500 face unit into the bracket as shown below.1010. Reconnect the power cables and other serial interfaces as normal.1011. Power on the POS and ViVOpay 4500. When lit, the leftmost LED indicates power is on.10Omni 375011Bracket and Saddle Installation111. Disconnect the power adapter and any other cables from the Omni unit.112. Turn the Omni unit so that the rear is facing up as shown in the figure below.113. Insert the Omni into the ViVOpay 4500 bracket.124. Slide the two prongs of the saddle into the applicable bracket slots and snap into place.125. Connect the ViVOpay 4500 serial cable to the Omni RS232 data port. Push the connector until the cable is locked in the port.126. Insert the ViVOpay power cable into the power module.127. Slide the ViVOpay 4500 into the saddle.128. Fit and gather the cables under the bracket. The resulting configuration is shown below.129. Power on the POS and ViVOpay 4500. When lit, the leftmost LED indicates power is on.12ViVOpay 4500 Window Mount.131. Obtain the following component:132. Determine the VP4500 placement on the window; using the alcohol cleaning pad to clean the window, it is important that the window be clean of any oily or greasy residue that will interface with the adhesive mounting overlay; let the window dry.133. Remove the adhesive covering on the overlay from the site marked “Peel this first”.134. Affix the VP4500 overlay to the window.145. Remove the second backing adhesive covering from the overlay.146. Affix the saddle onto the overlay adhesive; press to make sure saddle is firmly adhered to the overlay.147. Slide the bottom of the ViVOpay 4500 down into the saddle. Press the sides firmly until the tabs snap into place.158. Attach the serial cable to the POS and the power cable to the power supply.15Testing with Cards and Fobs16Troubleshooting17Glossary18Electronic Cash Register (ECR)18ExpressPay from American Express18Firmware18Fob18MasterCard PayPass18MTBF18NFC18NFC Phone18POS18Point of Sale (POS)18Proximity Payments18Radio Frequency (RF)19RF Reader19Visa Contactless19Customer Support20Customer Support20About ViVOtech20Размер: 600,1 КБСтраницы: 20Язык: EnglishПросмотреть
