Impex mp-6000 用户手册
SMITH MACHINE ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten all nuts and bolts until instructed to do so.
B.) Attach one Base Frame (#1) to the Left Vertical Frame (#3). Attach the Cross Brace (#6)
B.) Attach one Base Frame (#1) to the Left Vertical Frame (#3). Attach the Cross Brace (#6)
to the back of the Left Vertical Frame. Align the holes and secure the Base Frame, Left
Vertical Frame, and the Cross Brace together with two M10 x 2 3/8” Carriage Bolts (#83),
Ø ¾” Washers (#89), and M10 Aircraft Nuts (#90). Repeat the same procedure to install
the other side.
Vertical Frame, and the Cross Brace together with two M10 x 2 3/8” Carriage Bolts (#83),
Ø ¾” Washers (#89), and M10 Aircraft Nuts (#90). Repeat the same procedure to install
the other side.
C.) Attach a Guide Rod (#12) onto the Base Frame (#1). Secure it to the Base Frame with
one M10 x ¾” Allen Bolt (#76) and Ø ¾” Washer (#89) from the bottom.
D.) Slide one Lower Safety Stop Frame (#17) onto the Guide Rod from the top then slide one
Safety Stop Frame (#16) onto the Guide Rod.
E.) Attach a Front Vertical Frame (#2) onto the Base Frame (#1). Secure it with two M10 x 2
3/8” Carriage Bolts (#83), one 6” x 2 ¾” Bracket (#33), two Ø ¾” Washers (#89), and two
M10 Aircraft Nuts (#90).
M10 Aircraft Nuts (#90).
F.) Attach a Safety Hook (#18) to the Lower Safety Stop Frame (#17). Securely it with one
M10 x 1” Allen Bolt (#77), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90).
Attach the Safety Hook onto the selected slot on the back of the Front Vertical Frame.
Attach the Safety Hook onto the selected slot on the back of the Front Vertical Frame.
G.) Repeat Procedure C through F above to install the other side.
H.) Place the Front Top Beam (#5) onto the two Front Vertical Frames (#2).
I.) Insert the top of the Guide Rods (#12) into the holes on the Front Top Beam. Secure
H.) Place the Front Top Beam (#5) onto the two Front Vertical Frames (#2).
I.) Insert the top of the Guide Rods (#12) into the holes on the Front Top Beam. Secure
each Guide Rod to the Front Top Beam with one M10 x ¾” Allen Bolt (#76) and Ø ¾”
Washer (#89).
Washer (#89).
J.) Secure each Front Vertical Frame (#2) to the Front Top Beam (#5) with two M10 x 2 3/8”
Carriage Bolts (#83), one 6” x 2 ¾” Bracket (#33), two Ø ¾” Washers (#89), and two M10
Aircraft Nuts (#90).
Aircraft Nuts (#90).
K.) Secure the Front Top Beam to the Left Vertical Frame (#3) with four M10 x 4” Carriage
Bolts (#85), two Triangle Brackets (#20), four Ø ¾” Washers (#89), and four M10 Aircraft
Nuts (#90). Repeat the same procedure to secure the other side.
Nuts (#90). Repeat the same procedure to secure the other side.
7