Go-Video 4-Head Hi-Fi 用户手册
APPENDIX B - GLOSSARY
61
OTR
One Touch Recording. Each time you press REC after
the first time, you add 30 minutes to the record time.
For Loop Recording on the same tape (see page 22),
press until you see 9 min. 30 sec. on front panel
display; then press once more.
the first time, you add 30 minutes to the record time.
For Loop Recording on the same tape (see page 22),
press until you see 9 min. 30 sec. on front panel
display; then press once more.
PAUSE
Press this button to temporarily stop a tape while
playing (still) or recording (pause). If you leave Pause
on for 5 minutes, the VCR will automatically begin to
play to prevent tape damage.
playing (still) or recording (pause). If you leave Pause
on for 5 minutes, the VCR will automatically begin to
play to prevent tape damage.
PLAY
Press to play the tape in the active deck. Press and
hold 1.5 seconds for ATR.
hold 1.5 seconds for ATR.
POWER
Press on either the remote control or the front panel
of the VCR to turn your Dual-Deck VCR on and off.
The indicator light is on when the VCR is on and off
when the VCR is off. If the POWER key is pressed
while timer recording, copying a tape or rewinding,
the power light will blink. This indicates that the VCR
is in a power-off mode and that when the current func-
tion is complete, the VCR will automatically turn off.
of the VCR to turn your Dual-Deck VCR on and off.
The indicator light is on when the VCR is on and off
when the VCR is off. If the POWER key is pressed
while timer recording, copying a tape or rewinding,
the power light will blink. This indicates that the VCR
is in a power-off mode and that when the current func-
tion is complete, the VCR will automatically turn off.
RECORD SAFETY TAB
VHS tapes have a record safety tabs to protect you
from accidentally recording over your tapes. You
break this tab off to prohibit recording. If you later
wish to record on that tape, you can put a small piece
of tape over the opening.
from accidentally recording over your tapes. You
break this tab off to prohibit recording. If you later
wish to record on that tape, you can put a small piece
of tape over the opening.
REW
Press this button on the remote control while the
active deck is stopped to rewind the tape. Press while
the tape is playing to rewind while viewing the
picture. Press again while a tape is playing to speed
up picture rewind.
active deck is stopped to rewind the tape. Press while
the tape is playing to rewind while viewing the
picture. Press again while a tape is playing to speed
up picture rewind.
SAP
Secondary Audio Program. This indicator on the front
panel will be on if the TV program being broadcast
has a Secondary Audio Program signal. This audio
can be selected via the tuner audio selection in the
Tuner Setup menu.
panel will be on if the TV program being broadcast
has a Secondary Audio Program signal. This audio
can be selected via the tuner audio selection in the
Tuner Setup menu.
SEQUENTIAL PLAY
You can start a tape in Deck One and when it finishes
playing, a tape in Deck Two will automatically play.
See Playback Mode in the Features menu.
playing, a tape in Deck Two will automatically play.
See Playback Mode in the Features menu.
SLOW
Pressing these buttons slows the speed the tape is
playing. Successive pressing of the
playing. Successive pressing of the
+
key on the
remote control steps up the speed of the tape. Succes-
sive pressing of the
sive pressing of the
-
key on the remote control
slows down the speed of the tape. Press PLAY to
resume normal speed.
resume normal speed.
SP, LP, EP
This indicator on the front panel display shows the
tape speed for the selected deck. If you are playing a
tape, the tape speed is the speed at which the tape was
recorded. If you are recording, you can set the tape
speed - see Record Speed in the Deck Two menu.
tape speed for the selected deck. If you are playing a
tape, the tape speed is the speed at which the tape was
recorded. If you are recording, you can set the tape
speed - see Record Speed in the Deck Two menu.