Mitsubishi Electronics MR-MC210 用户手册
7 - 96
7. AUXILIARY FUNCTION
7.16.3 Control details
The operation details related to the amplifier-less axis function are shown below.
Item Operation
Servo amplifier
The specification of a supposedly connected servo amplifier is shown below.
SSCNET
communication method
Number of encoder pulses
per revolution [pulse]
Maximum motor speed
[r/min]
SSCNET /H 4194304
6000
Note. The servo amplifier operates as a servo amplifier compatible with a rotary servo motor. (It
does not operate as a servo amplifier compatible with the fully closed, linear, and direct
drive.)
drive.)
Home position return
Home position return using an incremental encoder or incremental linear scale including a scale
home position signal detection method and a scale home position signal detection method 2
(home position return which searches a home position signal again) cannot be used.
home position signal detection method and a scale home position signal detection method 2
(home position return which searches a home position signal again) cannot be used.
In-position signal (INP)
This signal turns on when the current command position and the current feedback position are
the same.
the same.
Servo alarm
No servo alarm occurs.
Servo information
Servo information (monitor No.0100 to 02FF) cannot be referred unless the servo amplifier is
connected. Servo amplifier is not connected (MESV) turns on.
connected. Servo amplifier is not connected (MESV) turns on.
High speed monitor
The current command position of the previous control cycle is displayed in the current feedback
position. Electrical current feedback and always 0 is displayed.
position. Electrical current feedback and always 0 is displayed.
Torque limit
By turning on/off the torque limit signal (TL), on/off of the selecting torque limit signal (TLSO)
can be confirmed. However, the torque limit effective signal (TLC) does not turn on and the
operation of the amplifier-less axis is not affected.
can be confirmed. However, the torque limit effective signal (TLC) does not turn on and the
operation of the amplifier-less axis is not affected.
Gain switching
By turning on/off the gain switching command signal (GAIN), on/off of the gain switching signal
(GAINO) can be confirmed. However, the operation of the amplifier-less axis is not affected.
(GAINO) can be confirmed. However, the operation of the amplifier-less axis is not affected.
Fully closed loop control change
By turning on/off the fully closed loop control change signal (CLD), on/off of the fully closed loop
control changing signal (CLDO) can be confirmed. However, the operation of the amplifier-less
axis is not affected.
control changing signal (CLDO) can be confirmed. However, the operation of the amplifier-less
axis is not affected.
PI-PID switching
By turning on/off the PID control command signal (CPC), on/off of the during PID control signal
(SPC) can be confirmed. However, the operation of the amplifier-less axis is not affected.
(SPC) can be confirmed. However, the operation of the amplifier-less axis is not affected.
Forced stop
When forced stop occurs, amplifier-less axis continues the positioning operation without
controller forced stop warning (servo warning E7).
controller forced stop warning (servo warning E7).
External signal
To simulate an operation using a limit switch signal or dog signal (such as home position return),
set dual port memory to the sensor input system (parameter No.0219) and control the sensor
signal command (LSPC, LSNC, DOGC) with the user program.
set dual port memory to the sensor input system (parameter No.0219) and control the sensor
signal command (LSPC, LSNC, DOGC) with the user program.
Absolute position detection
system
system
The absolute position detection system cannot be used. The incremental system is always
used.
used.
Reconnect/disconnect function
The amplifier-less axis cannot be disconnected or reconnected.
Operation with MR Configurator2
Servo amplifier cannot be operated or monitored with MR Configurator.
POINT
The operation of the current feedback position and the timing of the in-
position signal (INP) are different from the case where the servo amplifier is
connected. Confirm the operation finally with a real machine.
connected. Confirm the operation finally with a real machine.