Eureka! Tents N!ergy 1310 用户手册

1 Wired Tent Body with Guy Ropes, 6 Wall Poles, 3 Roof Poles, 1 Fly Pole, 1 Fly, 

1 Divider Curtain, 1 Carry Bag, 1 Stake Bag/Stakes and 1 Pole Bag

2. 

poles 

and divide according to size 

and shape. Take care; make sure 

that each pole section is fully 

seated into the next. Do not allow 

the sections to snap together as 

this can damage the ends. 

   See fig 2.

1. 

Remove from the carry bag 

and separate all the components. Unroll and unfold the 

fabric top side up, on a clean, dry space and open the doors. If windy, stake down the 

windward corner. See fig 1. 

4. 

Raise the tent. Start on one side and insert black wall poles into the corner elbows. At 

the bottom of each pole, insert the pin/ring (attached to the corner web) into the bottom 
of each pole. Next, install a blue pole at the center. With the blues, it works best to insert 
the ring/pin first and then fit the pole into the elbow. See fig 4.

Repeat on the other side until 

the tent is at full height 
and freestanding.

5. 

Attach all clips to the wall poles. See fig 5.

Stake the tent down through the corner web loops. Stake opposite corners while 

applying tension to smooth the floor wrinkles. Next, align the center poles and stake 
down. Do this before you add the fly

. 

See fig 6.

6.

 Attach the fly to the pole. Lay out the fly with the inside side up, on ground at the 

front of the tent. Fit the fly pole into the pockets sewn to the hem. The pole runs from 
side to side down the center of the fly. Secure the fly to the pole by wrapping the hook 
& loop fasteners around the fly pole. See fig 7, 8 and 9.

7. 

Attach the fly to the tent. Turn the fly assembly over and align it 

so that the pole ends point to the side windows. Grasp the corners 

of the of the fly and drag them up and over the roof poles to 

completely cover the roof. (This is much easier with two people.) 

The end of the poles should point out over the windows.

At the corners of the tent, reach under the fly and attach the hook & 

loop straps to the wall poles, securing the fly in place. See fig 10.

At the bottom/corners of the tent, attach the shockcorded J-hooks 

to the nylon rings on the corner web loops. See fig 11.

8. 

Stake out the attached guy ropes and adjust tension with the 

in-line sliders. Also, there is a vent beneath each of the side 

windows. Attach the included cords and stake out. See fig 12.

fig 2

fig 1

fig 5

fig 3

fig 6

fig 11

fig 12

fig 7

fig 8

fig 9

fig 10

3. 

into the sleeves sewn on the tent body. They should run 

corner to corner crossing in the center.

Fit one end of each into a nylon elbow attached to the roof corners at 

A and B. Move to 

the opposite side, arch the poles and again fit into the nylon elbows at 

C and D. 

Insert the blue roof pole, front to back, into the tan color coded sleeves from 

E to F. 

See fig 3.

fig 4

REV. D  4.09

fig 14

green

blue

fig 13

E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold 

separately. Once connected to power, the control will display “green” at any switch that 

is “ON” and the “ON” socket will glow blue. See fig 13. 

E! Power Port: Open zipper and run extension cord through opening. Close zipper so that it 

rests next to the extension cord. Make sure the zipper cover is not twisted or tucked. The 

cover must lay flat against the outside of the tent to keep out rain.

Sweep Out: Inside, at the bottom of the 

door is a sewn-in web loop. Pull this loop 

to the outside and stake it down to 

provide a ready exit for floor sweepings. 

See fig 14. 

Take Down: Pull up all stakes. Release the 

fly’s hook & loop straps. Remove fly. 

Remove fly poles. Remove clips from tent 

poles and pull poles off of the pins. 

Collapse all poles and stow. Fold the tent 

onto itself then fold the fly and lay it on 

tent. Roll up both towards the open door 

and stow.