Linksys DES-3028/DES-3028P/DES-3052/DES-3052P 用户手册
DES-3028 DES-3028P DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual
23
T
IME
R
ANGE
C
OMMANDS
The Time Range commands are used in conjunction with the Access Profile commands listed in the previous chapter to determine
a starting point and an ending point, based on days of the week, when an Access Profile configuration will be enabled on the
Switch. Once configured here, the time range are to be applied to an access profile rule using the config access_profile profile_id
command.
a starting point and an ending point, based on days of the week, when an Access Profile configuration will be enabled on the
Switch. Once configured here, the time range are to be applied to an access profile rule using the config access_profile profile_id
command.
NOTE: The Time Range commands are based on the time settings of the Switch.
Make sure to configure the time for the Switch appropriately for these commands
using commands listed in the following chapter, Time and SNTP Commands.
Make sure to configure the time for the Switch appropriately for these commands
using commands listed in the following chapter, Time and SNTP Commands.
The Time Range commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.
following table.
Command Parameters
config time_range
<range_name 32> [hours start_time <time hh:mm:ss> end_time <time
hh:mm:ss> weekdays <daylist> | delete]
hh:mm:ss> weekdays <daylist> | delete]
show time_range
Each command is listed, in detail, in the following sections.
config time_range
Purpose
Used to configure a time range in which an access profile rule is to be
enabled.
enabled.
Syntax
config time_range <range_name 32> [hours start_time <time hh:mm:ss>
end_time <time hh:mm:ss> weekdays <daylist> | delete]
end_time <time hh:mm:ss> weekdays <daylist> | delete]
Description
This command is to be used in conjunction with an access profile rule to
determine a period of time when an access profile and an associated rule are
to be enabled on the Switch. Remember, this time range can only be applied
to one period of time and also, it is based on the time set on the Switch.
determine a period of time when an access profile and an associated rule are
to be enabled on the Switch. Remember, this time range can only be applied
to one period of time and also, it is based on the time set on the Switch.
Parameters
range_name 32 – Enter a name of no more than 32 alphanumeric characters
that will be used to identify this time range on the Switch. This range name
will be used in the config access_profile profile_id command to identify the
access profile and associated rule to be enabled for this time range.
hours – This parameter is used to set the time in the day that this time range
is to be set using the following parameters:
that will be used to identify this time range on the Switch. This range name
will be used in the config access_profile profile_id command to identify the
access profile and associated rule to be enabled for this time range.
hours – This parameter is used to set the time in the day that this time range
is to be set using the following parameters:
weekdays – Use this parameter to determine the days of the week to set this
time range.
time range.
delete – Use this parameter to delete a previously configured time range from
the system.
the system.
Restrictions Only
administrator-level users can issue this command.
start time <time hh:mm:ss> - Use this parameter to identify the
starting time of the time range, in hours, minutes and seconds,
based on the 24-hour time system.
starting time of the time range, in hours, minutes and seconds,
based on the 24-hour time system.
•
•
•
end time <time hh:mm:ss> - Use this parameter to identify the
ending time of the time range, in hours, minutes and seconds,
based on the 24-hour time system.
ending time of the time range, in hours, minutes and seconds,
based on the 24-hour time system.
<daylist> - The user may set the days of the week here to set this
time range in the three letter format (mon, tue, wed…). To specify a
day range, separate the daylist using a dash (mon-fri would mean
Monday through Friday). To specify a list of days in a week,
separate the daylist using a comma, with no spaces (mon,tue,fri
would mean Monday, Tuesday and Friday).
time range in the three letter format (mon, tue, wed…). To specify a
day range, separate the daylist using a dash (mon-fri would mean
Monday through Friday). To specify a list of days in a week,
separate the daylist using a comma, with no spaces (mon,tue,fri
would mean Monday, Tuesday and Friday).
164