Roland AR-200 用户手册
52
Error messages
If an incorrect operation is attempted or execution is not
possible, an error message will appear in the display. Note
the message that appears, and take the appropriate action.
possible, an error message will appear in the display. Note
the message that appears, and take the appropriate action.
fig.er-3
Situation:
It is possible that the data in the PC card or the
PC card itself has been damaged.
PC card itself has been damaged.
Action:
Delete all phrases (p. 25). If delete card is not
possible, or if the same message appears after
the card has been delete card, it may be that
the PC card is malfunctioning. Use a different
PC card.
possible, or if the same message appears after
the card has been delete card, it may be that
the PC card is malfunctioning. Use a different
PC card.
fig.er-4
Situation:
The card is of a type which the AR-200 is not
able to use.
able to use.
Action:
Refer to the section "Reccomended PC cards"
(p. 66) and use an appropriate PC card.
(p. 66) and use an appropriate PC card.
fig.er-5
Situation:
No more data can be recorded in the card.
Action:
Either delete unnecessary phrases (p. 25), or
use a different card.
use a different card.
fig.er-6
Situation:
Either the phrase data is damaged, or the
AR-200 is not able to handle the phrase.
AR-200 is not able to handle the phrase.
Action:
Check the phrase for which the message was
displayed.
displayed.
fig.er-7
Situation:
The write protect switch on the PC card is set
to the ON position.
to the ON position.
Action:
Refer to the manual for the PC card, and set
the write protect switch to the OFF position.
the write protect switch to the OFF position.
fig.er-8
Situation:
The backup battery in the PC card has run down.
Action:
Refer to the manual for the PC card and
replace the battery.
replace the battery.
fig.er-9
Situation:
A large amount of MIDI data was received in a
short time, and could not be processed.
short time, and could not be processed.
Action:
Change the way in which MIDI data is being
transmitted.
transmitted.
fig.er-10
Situation:
Once an Active Sensing message was received,
300 msec elapsed without any message being
received.
300 msec elapsed without any message being
received.
Action:
Check the MIDI cable connect or turn off.
fig.er-11
Situation:
The PC card is not formatted for use with the
AR-200.
AR-200.
Action:
Format the PC card.
fig.er-12
Situation:
There is no phrase corresponding to the
specified phrase.
specified phrase.
Action:
Select a saved phrase or record a new phrase.
fig.er-13
Situation:
Data was not written to or read from the card
in time.
in time.
Action:
Change the RDAC-Grade, RDAC-Mode, or
other recording conditions to reduce the
amount of data.
other recording conditions to reduce the
amount of data.
fig.er-14
Situation:
Card protect is set to ON, so data cannot be
written to the card.
written to the card.
Action:
Set card protect to OFF.
fig.er-15
Situation:
The AR-200 gets hot.
Action:
Ventilate well to avoid overheating, and keep
the unit cool.
the unit cool.
fig.er-16
Situation:
Cannot overwrite or make changes on a card
formatted for the AR-2000.
formatted for the AR-2000.
Action:
Use a card after formatting it on the AR-200, or
otherwise use an AR-3000 format card.
otherwise use an AR-3000 format card.
Situation:
Checksum error found in received MIDI data.
Action:
Check the transmission status and the MIDI
data.
data.
AR-200_e.book 52 ページ ２００３年７月１４日 月曜日 午後１時１１分