Roland AR-3000R 用户手册
116
Controlling the AR-3000R Using MIDI Signals (MIDI Control)
Procedure for Setting the MTC Error Level
1.
Press the MODE button.
The MODE indicator lights up.
2.
Use the SELECT dial to choose “6.9 MTC,” then press the
dial.
dial.
3.
Press the SELECT dial to advance the input location
(highlighted) to “MTC Error Level.”
(highlighted) to “MTC Error Level.”
4.
Turn the SELECT dial to choose the MTC Error Level
(from 0 to 10), then press the dial.
(from 0 to 10), then press the dial.
fig.16-g18e
5.
When the prompt appears on the screen, press the
ENTER button to enable the settings.
ENTER button to enable the settings.
To quit without making the settings, use the SELECT dial to
choose “NO,” then press the ENTER button.
choose “NO,” then press the ENTER button.
Once the settings have been successfully modified, you’re
returned to the setting item selection screen.
returned to the setting item selection screen.
6.
Press the MODE button.
This ends the setting process and returns you to the usual
screen.
screen.
* While making the settings, you can go back to the previous
entry position (highlighted) by using the PAUSE (BACK)
button.
button.
* If you press the MODE button while making settings, a
message asking you to confirm that you want to exit the setting
process appears. Note that if you choose “YES,” then press the
ENTER button, you are returned to the usual screen, and all
setting changes you’ve made up to that point will be discarded.
process appears. Note that if you choose “YES,” then press the
ENTER button, you are returned to the usual screen, and all
setting changes you’ve made up to that point will be discarded.
Operation Procedures
When you have finished making the settings, carry out
playback on the connected master device. Phrase playback in
sync with received MIDI time codes starts.
playback on the connected master device. Phrase playback in
sync with received MIDI time codes starts.
When Sync Source is set to MTC, the indicators on the front
panel of the unit light up as shown below.
panel of the unit light up as shown below.
fig.16-08e
• Playback is paused when MTC (Full messages; p. 139) is
received, or the PLAY button is pressed.
• To enter recording standby under the control of MTC,
press the PLAY button while holding down the STOP
button, then press the PAUSE button again.
button, then press the PAUSE button again.
A screen like the following appears during playback.
fig.16-08ae
Note that there is no operation unless MIDI time codes are
input from the external MIDI instrument.
input from the external MIDI instrument.
AR-3000R Settings (When the
AR-3000R Is the Master)
AR-3000R Is the Master)
Selection of MIDI Output (MIDI OUT or
MIDI THRU)
MIDI THRU)
This switches the functioning of the MIDI output connector.
Here, select “OUT.”
Here, select “OUT.”
OUT:
This sends MIDI information from the unit. Select this
when you want to play back MIDI phrases, send Exclusive
(SysEx) messages, or make the AR-3000R the master during
synchronization using MIDI signals.
(SysEx) messages, or make the AR-3000R the master during
synchronization using MIDI signals.
THRU:
This takes MIDI information from MIDI IN and sends
it out unchanged. MIDI information from the AR-3000R itself
is not output.
is not output.
Procedure for Setting MIDI Output (MIDI OUT
or MIDI THRU)
or MIDI THRU)
PLAY button
PAUSE button
During Pause
During Rec standby
Lights in green
Lights in red
Lights in orange
Lights in orange
Remaining time for phrase playback
MIDI Time Code
AR-3000R_e.book 116 ページ ２０１０年３月１８日 木曜日 午後２時６分