Roland AR-3000R 用户手册
58
Modifying Recorded Phrases (Phrase Settings)
Procedure for Making Loop Play Settings
1.
Use the SELECT dial to choose the phrase whose setting
you want to change.
you want to change.
2.
Press the MODE button.
The MODE indicator lights up.
3.
Use the SELECT dial to choose “1.5 Loop Play,” then
press the dial.
press the dial.
You can reselect a phrase whose setting you want to change
by pressing the PAUSE (BACK) button. The entry position
(highlighted) moves to the phrase selection, so turn the
SELECT dial to reselect card A or B and the phrase number,
then press the dial.
by pressing the PAUSE (BACK) button. The entry position
(highlighted) moves to the phrase selection, so turn the
SELECT dial to reselect card A or B and the phrase number,
then press the dial.
4.
Turn the SELECT dial to choose Loop (OFF/ON/1 to 99),
then press the dial.
then press the dial.
fig.11-g05e
Turn the SELECT dial to set the Loop 1 position (time), then
press the dial. Pressing the dial while the cursor
(highlighting) is at the “sf” position moves the Loop 2
position setting.
press the dial. Pressing the dial while the cursor
(highlighting) is at the “sf” position moves the Loop 2
position setting.
* The time that is set is shown as a relative amount of time, with
the start position of the playback point taken to be 0.
* Each press of the BACK button moves the cursor (highlighted)
in the sequence of sf
→
f
→
s
→
m
→
h.
Turn the SELECT dial to set the Loop 2 position (time), then
press the dial.
press the dial.
* The looped region cannot be set to value less than 10 frames.
You can set the points while listening to the audio by using
the SCRUB playback mode (Owner’s Manual p. 54). You can
check the Loop 1 and Loop 2 junctures using the Preview
playback mode.
the SCRUB playback mode (Owner’s Manual p. 54). You can
check the Loop 1 and Loop 2 junctures using the Preview
playback mode.
5.
Turn the SELECT dial, select the Crossfade Time (0
ms to 1000 ms), then press the dial.
6.
When the prompt appears on the screen, press the
ENTER button to enable the settings.
ENTER button to enable the settings.
To quit without making the settings, use the SELECT dial to
choose “NO,” then press the ENTER button.
choose “NO,” then press the ENTER button.
Once the settings have been successfully modified, you’re
returned to the setting item selection screen.
7.
Press the MODE button.
This ends the setting process and returns you to the usual
screen.
screen.
* While making the settings, you can go back to the previous
entry location (highlighted) by pressing the PAUSE (BACK)
button.
button.
* If you press the MODE button while making settings, a
message asking you to confirm that you want to exit the
setting process appears. Note that if you choose “YES,” then
press the ENTER button, you are returned to the usual screen,
and all setting changes you’ve made up to that point will be
discarded.
setting process appears. Note that if you choose “YES,” then
press the ENTER button, you are returned to the usual screen,
and all setting changes you’ve made up to that point will be
discarded.
If a start or end playback point is set within the looped
interval, the start point is set to Loop 1 and the end point is
set to Loop 2.
interval, the start point is set to Loop 1 and the end point is
set to Loop 2.
Fade (Fade In and Fade Out)
This makes the settings for starting phrase playback with a
Fade In and ending playback with a Fade Out.
Fade In and ending playback with a Fade Out.
This sets the time until the playback level is reached from
silence (Fade In) and the time until silence is reached from
the playback level (Fade Out).
silence (Fade In) and the time until silence is reached from
the playback level (Fade Out).
fig.11-06e
If there is noise or the like at the beginning or end of a
phrase, you can cause the noise component not to be played
back simply by setting the Fade In or Fade Out times to Time
1 through Time 3.
phrase, you can cause the noise component not to be played
back simply by setting the Fade In or Fade Out times to Time
1 through Time 3.
Time1: Set at approx. 10 msec.
Time2: Set at approx. 30 msec.
Time3: Set at approx. 50 msec.
fig.11-07e
Phrase
Loop passage
Phrase
Fade In
(Time)
Fade Out
(Time)
Phrase
Removal effect when noise or the like is present
Around 10 to 50 milliseconds
AR-3000R_e.book 58 ページ ２０１０年３月１８日 木曜日 午後２時６分