Canon 5178B002 产品宣传页

CT1-8586-000 

1206SZ 

© CANON INC. 2012

ON

STABILIZER

OFF

●

❺

●

❼

●

❻

Button

You can use the Image Stabilizer in AF or MF mode.

This function provides optimal image stabilization depending on 

shooting conditions (such as shooting still subjects and following shots).

1. Set the STABILIZER switch to ON ❺ .

●

 If you are not going to use the image stabilizer function, set the 

switch to OFF.

2. When you press the shutter button halfway, the Image Stabilizer will 

start operating.

●

 Make sure the image in the viewfinder is stable, then press the shutter 

button the rest of the way down to take the picture.

●

 The Image Stabilizer cannot compensate for a blurred shot 

caused by a subject that moved.

●

 The Image Stabilizer may not be fully effective if you shoot from 

a violently shaking vehicle or other transportation.

●

 The Image Stabilizer consumes more power than normal 

shooting, so fewer shots can be taken if you use the function.

●

 When shooting a still subject, it compensates for camera shake 

in all directions.

●

 It compensates for vertical camera shake during following 

shots in a horizontal direction, and compensates for horizontal 

camera shake during following shots in a vertical direction.

●

 When you use a tripod, the Image Stabilizer should be turned 

off to save battery power.

●

 The stabilizer is equally effective for handheld photography and 

photography with a monopod. The Image Stabilizer effect may 

be reduced, however, depending on the shooting environment.

●

 The Image Stabilizer also operates when the lens is used with 

extension tube EF12 II or EF25 II.

●

 If you set the camera’s Custom Function to change the 

assigned button to operate the AF, the Image Stabilizer will 

operate when you press the newly assigned AF button.

The EW-72 hood can keep unwanted light out of the lens, and also 

protects the lens from rain, snow, and dust.

To attach the hood, align the hood’s attachment position mark with the 

red dot on the front of the lens, then turn the hood in the direction of 

the arrow until the lens’s red dot is aligned with the hood’s stop position 

mark ❻ .

To remove the hood, hold down the button on the side and turn the hood 

in the direction of the arrow until the position mark on the hood aligns 

with the red dot ❼ .

The hood can be reverse-mounted on the lens for storage.

●

 Part of the picture may be blocked if the hood is not attached properly.

●

 When attaching or detaching the hood, grasp the base of the hood to 

turn it. To prevent deformation, do not grasp the rim of the hood to turn it.

You can attach filters to the filter mounting thread on the front of the lens.

●

 Only one filter may be attached.

●

 Use a polarizing Canon filter (67mm).

●

 To adjust the polarizing filter, first remove the lens hood.

You can attach extension tube EF12 II or EF25 II for magnified shots. 

For shooting distance and magnification, see the extension tube 

specifications.

MF mode is recommended for accurate focusing.

●

The extenders cannot be used with this lens. 

●

The close-up lenses cannot be used with this lens. 

●

CASE (Sold Separately) LP1116

This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference, and (2) 

this device must accept any interference received, including interference that may 

cause undesired operation.

Do not make any changes or modifications to the equipment unless otherwise 

specified in the instructions. If such changes or modifications should be made, you 

could be required to stop operation of the equipment.

This equipment has been tested and found to comply with the limits for a class B 

digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one or more of the following 

measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Consult the dealer or an experienced radio/TV technician for help.

* Sold Separately

Angle of view

Lens 

construction

Minimum 

aperture

Max. 

magnification

Min. focusing 

distance

Filter 

diameter

Max. diameter and 

length

Weight

Hood* Lens Cap Case*

Diagonal Vertical Horizontal

EF35mm f/2 IS USM

63°

38°

54°

8-10

22

0.24x

0.24m/0.79ft

67mm

77.9x62.6mm 

(3.1”x2.5”)

335g/11.8oz EW-72

E-67ll

LP1116

Magnification

(X)

Focusing Distance Range

(mm) (inch)

EF35mm f/2 IS USM

EF12 II

0.60-0.36

168-197 (6.6-7.6)

EF25 II

1.04-0.79

158-160 (6.2-6.3)

COP

Y