Oregon Scientific ATC9K 产品宣传页

1

2

3

7

8

9

4

6

Press the On/Off Button 

 . 

A start up screen will be shown on the LCD.

•  Keep the rechargeable battery dry.

•  Replace only with the same type recommended by Oregon Scientific.

•  Dispose of the used rechargeable battery promptly as described in the instructions.

•  Turn the camera off before removing the rechargeable battery or the microSD 

    card. The card and the data may be damaged if the microSD card is inserted 

    or removed while the camera is still on.

•  Remove the rechargeable battery and the microSD card before storing the 

    camera for long periods of time. Keep it in a well-ventilated place to prevent 

    mould.

•  Under the following circumstances, have the camera repaired by qualified

    personnel:

    a) The plug is damaged or worn.

    b) The device has been dropped and/or the housing has been damaged.
    c) Liquid has entered the camera.

Oregon Scientific will not, under any circumstances, be responsible for injuries 

or property damage incurred during participation of any high-risk sports or 

activities not endorsed or recommended by Oregon Scientific. Should the 

camera malfunction under these circumstances, it will not be covered under 

warranty.  The warranty covers manufacturing defects only.

Users are asked to note that the transfer of memory containing photos or data 

protected under copyright laws is only permissible within the restrictions imposed.

Users assume all responsibility in the event that copyrights are violated by the 

use of this camera.

The ATC9K camera is waterproof up to 20m (60ft). Oregon Scientific will not 

assume any responsibility for camera malfunction caused by liquid entering the 

camera as a result of misuse by the user.

• Supports Micro SD/SDHC Class 4 card or above and compatible up to 32GB  

  (not included).

• Movie storage:  

  1080p = 1920x1080 pixels (16:9), 30 fps, ~12 Mbit/s data rate, approximately 

  9 minutes of video per 1G Byte

  720p = 1280x720 pixels (16:9), 60 fps, ~12 Mbit/s data rate, approximately 

  10 minutes of video per 1G Byte

   720p = 1280x720 pixels (16:9), 30 fps, ~8 Mbit/s data rate, approximately 15 

   minutes of video per 1G Byte

   WVGA = 848x480 pixels (16:9), 60 fps, ~8Mbit/s data rate, approximately 15 

   minutes of video per 1G Byte

  The recording durations will be varied which depends on the recording 

  objects and environment.

• 320 x 240 Color LCD screen 

• Focusing range 3m~infinity

• Movie images MOV

• USB Interface (2.0)

• Monitor Interface HDMI (1.3)

• Rechargeable battery (included)

• Dimensions 40mm diameter. x 103mm length

• Operation system WinXP/Vista /7 or Apple Mac X 10.6 or above

•  Windows Environment: 3.0 Ghz Intel Pentium D (dual-core) or faster 

•  Mac Environment: Dual 2.0 GHz PowerMac G5 or faster; 2.0 GHz Intel Core 

   Duo or faster

• Windows XP (Service Pack 2 or later), Windows Vista, Windows7 or Apple 

   Mac X 10.6 or above

• 2GB RAM

• 1G Free hard disk space

• 1GB or greater video card 

• Quicktime 7

• 1024x768 resolution video support (32 bit)

• 16 bit Windows compatible sound device

Thank you for purchasing the ATC9K Action Camera, this package should contain the:

1. Main Camera Unit with Camera Grip
2. Carrying Bag
3. Software Installation CD
4. Remote Control
5. Rechargeable Battery
6. Long Silicon Strap
7. Long Velcro Strap
8. Helmet Grip
9. Handlebar Mount
10.Base Mount and Tripod Mount
11.Rubberized Patch
12.Velcro Patch
13.USB Cable
14.HDMI Cable
15.User Manual
16.Screw
17.Nut

18.GPS Module

19.External Battery Charger

Press the On/Off button 

 . A start up screen will be shown on the 

LCD screen.

1.  The system will ask you to set the Date/Time/Timezone when 

the camera is turned on for the first time or the rechargeable 
battery is reinstalled.

2.  Press 

 

 to select your options. Press 

 to confirm your 

selections.

1. Aim at what you want to record.

2. To start recording press the “Movie shutter button”

     

 at the top of the camera.

3. The Laser Pointer at the front of the camera will be 

turned on for a more accurate adjustment of the target. 

Users can set the turn on time of the Laser Pointer in User Settings.

4. The Laser Pointer will be turned off according to the user selected time. 

Then the camera will start recording (one sound effect with red LED light 

flashing). The Movie shutter icon will blink on the top left corner of the 

screen while the time elapsed will be shown at the bottom of the screen.

5. To stop recording press the “Movie shutter button” 

 at the top of the 

camera again.

1. Aim at what you want to capture.

2. Press the “Photo capture button” 

 at the top of the 

camera.

3. A shutter sound and the red LED will blink once to 

    indicate that a photo was taken. A preview will be 

shown on the LCD screen briefly.

1. Press the “Play/Pause” 

, then the screen will switch to playback mode.

2. Press “Left” and “Right” button 

 

 to select the video or photo that you 

want to playback.

3. During video playback, press “Play/Pause” 

 , to pause or resume playback, 

press “Left” and “Right” button 

 

 to activate fast 

forward and fast reverse. 

4. To exit the playback mode, press “Movie shutter” button 

 or “Photo Capture” button 

.

1. Press the “Menu” button 

 

during playback mode, select the video or file 

you want to delete with “Left” and “Right” button 

 

.

2. Then press “Play/Pause” 

 to confirm deletion after 

the dialogue box pops up.

1. Ensure you are pointing the remote control sensor towards the front of the 

camera. Press either the “Movie shutter” button 

 or “Photo Capture”

    button 

.

2. The red LED will flash to show recording or photo capturing has started.

3. The buttons on the remote control carries the same functions as those found 

on the back of the camera.

No SD Card Inserted

(Remove Red Line if inserted)

Privacy Mode On

(disappear when Off)

Video Resolution

EV

Video/Photo Quality

Photo Resolution

Night Mode On

(disappear when Off)

Cont’ Shots On 

(disappear when Off)

White Balance Setting

Battery 

(4 states)

Lapse Time (when recording and playback)

Remaining  Time (when viewing)  

G Sensor On

(disappear when Off)

GPS On

(disappear when Off or no 

module) 

There are 5 main camera settings which are Video, Photo, G-Sensor, 
GPS and General Settings. The GPS setting is activated only when the 
GPS module (sold separately) is attached onto the camera. 

1.  To enter into Settings, press “Menu” button 

 in the live 

     view mode.
2.  You can scroll through these categories by pressing “Left” 
     and “Right” buttons 

 

.

3.  To enter the category, press “Play/Pause” button 

.

4.  To select a setting, press “Play/Pause” button 

.

5.  To select options under a setting, press “Left” and “Right” 
     buttons 

 

.

6.  To confirm an option, press “Play/Pause” button 

.

7.  To exit settings, press “Menu” button 

 again.

     You can set your video resolution here.

2. Quality
    You can select Fine, Good or Normal.

     The Exposure values range from +2.0 to -2.0. You can set the appropriate value to suit 
     your shooting environment.

     Based on different surroundings, you can select Auto, Daylight, Cloudy, Fluorescent and 
     Tungsten to adapt a correct color tone of the video. 

     According to your preference, you can adjust the contrast level with Standard, Soft, Hard.

     According to your preference, you can adjust the sharpness with Standard, Soft, Hard.

     You can add effects to the video too. Just select Vivid, Negative, Black and White, 
     Sepia or Art.

     To record a video with a time limit, select a duration here.

     You can set your photo resolution here with either 3megapixels or 5megapixels.

     You can select Fine, Good or Normal.

     You can turn it on in order to have a boost of exposure during the night.

     The Exposure values range from +2.0 to -2.0. You can set the appropriate value to 

     suit your shooting environment.

Full HD/30 

              1920x1080, 30 fps

HD/60                                      1280x720, 60 fps
HD/30          

              1280x720, 30 fps

WVGA         

              848x480, 60 fps

1      Play/Pause button 

Play/Pause/Confirm

2      Left button 

                  Left

3      Menu button 

                  Settings menu

4      Right button 

                  Right

5      Power On-Off                    Power on/off unit
6      Movie Shutter button 

Record start/stop

7      Photo Capture button 

Take photo

8      USB Connection 

Connect to the computer

9      HDMI Connection 

Connect to the TV

10     microSD card slot 

Insert microSD card

11     Battery Compartment 

Insert rechargeable battery

12     GPS Module slot                 Insert GPS Module

5

10

11

      According to different environment, you can select Auto, Daylight, Cloudy, Fluorescent 

      and Tungsten to adapt a correct color tone of the photo. 

      According to your preference, you can adjust contrast level with Standard, Soft, Hard.

      According to your preference, you can adjust sharpness with Standard, Soft, Hard.

      You can add effects to the video too. Just select Vivid, Negative, Black and White,   
      Sepia or Art.

      You can set a countdown time before the shutter captures automatically.

       You can set the camera to either take 3 or 5 continuous shouts with this setting.

       You can set the camera to take photos within a certain time interval.

     You can turn on or off the G-Sensor here. Power consumption can be reduced by turning 
     off the G-Sensor.

     You can display G-Sensor related data on the videos and photos via HDMI output by  

     turning on this setting.

GPS Module is sold separately. Please refer to the corresponding manual for these settings.

    This setting allows you to have either 5 or 10 seconds to adjust the direction of the  
    camera using the laser pointer before the capturing of videos after you press the “Movie 
    Shutter” button 

.

     You can adjust the sound volume here.

    The sensitivity of the microphone can be adjusted with this settings. If “Off” is selected,   
    that means the audio signal is being turned off.

     With Privacy mode on, all LED and Audio indicators will be turned off.

      Date and time will be stamped on the videos and photos with this setting being 
      turned on.

      This setting controls the sleep time of the LCD screen. While the LCD is sleeping, 

      power consumption is reduced.

      Sometimes you may want the camera to turn off automatically during idle. 

      Set your preference here to do so.

      Set your date here.

      Set your time here.

      Set your timezone here.

       Set your system language here.

       In order to avoid flickering in the video while shooting indoors, you need to adjust 

       this setting to match the frequency of light source with that of the shutter.

       The background music being played when the camera is turned on and off, can be  

       switched to on or off by this setting.

       You can format the microSD card inserted in the camera with this setting.

       Restore back to the factory default settings. 

       This setting will display an on-screen metre for users to   
       adjust the horizontal and vertical position of the camera.  
       The green dots represent the extend of the tilting 
       deviations. The camera unit is placed horizontally and   
       vertically neutral only when the centre green dots lights     
       up.

       Display the current system version.

(Items sold separately)

1    Play/Pause button              Play/Pause/Confirm
2    Left button 

               Left

3    Right button 

               Right

4    Menu button 

               Settings menu

5    Movie Shutter button         Record/Stop button
6    Photo Capture button         Take photo

• Sensor resolution 5M pixels CMOS.

  

Display the video resolution setting.

Display the photo resolution setting.

Display the EV value.

Display the quality setting of the videos & photos.
Indicate that there is no microSD card inserted. The red line will disappear when a 

microSD card is inserted.
Privacy Mode is on. It will disappear when it is disabled in the user settings.

GPS function is on. It will disappear when the camera is not equipped with the 

GPS module or it is disabled in the user settings.

G-Sensor function is on. It will disappear when it is disabled  in the user settings.

Continuous shots function is on. It will disappear when it is disabled in the user 

settings.

Self timer function is on. It will disappear when it is disabled in the user settings.

Night Mode is on. It will disappear when it is disabled in the user settings.

Display the white balance setting.

Display the battery status.

OREGON SCIENTIFIC and associated trademarks and trade dress are owned by 
OREGON SCIENTIFIC, Inc.
© 2011 OREGON SCIENTIFIC, Inc. All Rights Reserved.

Notice the following guidelines when using your camera

•  The ATC9K is shock resistant, not shock proof.

•  For your safety, do not press the buttons on the camera during sports activities.

•  Do not place the camera in areas prone to dust or damp for extended periods 

   of time. This may cause a fire or an electrical shock.

•  Do not leave the camera in places exposed to extremely high temperatures, 

    such as under direct sunlight, for extended periods of time.  This may affect 

    the camera housing and internal components.

•  Clean the lens with a soft cloth to remove fingerprints or dust.

•  If the rechargeable battery is mishandled, it can burst, cause a fire or even 

   chemical burns. Observe the following cautions.

•  Do not disassemble.

•  Do not crush and do not expose the rechargeable battery to any shock or force 

   such as hammering, dropping or stepping on it.

•  Do not short circuit and do not allow metal objects to come into contact with 

   the battery terminals.

•  Do not expose to extreme temperatures below 0°C (32°F) or above 40°C (104°F).

•  Do not incinerate or dispose of in fire.

•  Do not handle the damaged or leaking rechargeable battery.

•  Be sure to charge the rechargeable battery using a genuine ATC9K battery 

   charger or charge it via the main unit.

•  Keep the rechargeable battery out of the reach of small children.

1. Aim the ATC9K at what you would like to take a picture.

2. Press the Photo capture button 

 at the top of the camera.

3. The LCD display will be frozen for a while, indicates that the scene had been 

    captured.

1. Aim the ATC9K at what you would like to record.

2. To start recording press the Movie shutter button 

 at the top of the camera.

3. Press the movie shutter button 

 again to stop recording. An animation showing 

    a circular motion will appear, which indicates the footage is being saved.

• If the camera gets wet, wipe the liquid off as soon as possible with a dry cloth.

• Other camera accessories may not be waterproof. 

GPS function is on but the GPS module is either searching or establishing connections 
with satellites. The process will take minutes to complete but the duration depends 
on the surroundings of your location as well as weather conditions.

 * In some cases, the frame rate may be automatically reduced to maximize the 

    memory usage. 

Interval shots function is on. It will disappear when it is disabled in the user settings.

ATC9K US manual 16DEC R15.indd   1

12/16/11   3:52:33 PM