Panasonic PV-GS180 用户手册
Others
66
LSQT0973
6: The cassette cannot be removed.
• Does the status indicator come on when
• Does the status indicator come on when
opening the cassette cover? (
-19-
) Make sure
that the battery and the AC adaptor are
properly connected. (
properly connected. (
-16-
)
• Is the battery in use discharged? Charge the
battery and remove the cassette.
• Close the cassette cover completely, and fully
open it again. (
-17-
)
7: No operation other than cassette removal
can be performed.
• Has condensation occurred? Wait until the
condensation indication disappears. (
-68-
)
8: The remote control does not function.
• Has the button-type battery of the remote
• Has the button-type battery of the remote
control run out? Replace it with a new
button-type battery. (
button-type battery. (
-24-
)
• Is the setting on the remote control correct? If
the setting on the remote control is not in
agreement with the [REMOTE] setting on the
Camcorder, the remote control does not
operate. (
agreement with the [REMOTE] setting on the
Camcorder, the remote control does not
operate. (
-25-
)
Recording
1: Recording does not start although power is
1: Recording does not start although power is
supplied to the Camcorder and the cassette
is correctly inserted.
is correctly inserted.
• Is the accidental erasure prevention slider on
the cassette open? If it is open (set to [SAVE]),
recording cannot be performed. (
recording cannot be performed. (
-18-
)
• Is the tape wound to the end? Insert a new
cassette.
• Is the recording mode set? When in the
playback mode, recording cannot be
performed. (
performed. (
-26-
)
• Has condensation occurred? No operation
other than cassette removal can be performed
when condensation occurs. Wait until the
condensation indication disappears. (
when condensation occurs. Wait until the
condensation indication disappears. (
-68-
)
• Is the cassette cover open? If the cover is
open, the Camcorder may not operate
normally. Close the cassette cover. (
normally. Close the cassette cover. (
-17-
)
2: The screen has changed suddenly.
• Has the demonstration started? In the Tape
• Has the demonstration started? In the Tape
Recording mode, if you set [DEMO MODE] >>
[ON] without inserting a cassette and a card,
the demonstration starts. For normal use, set
this function to [OFF]. (
[ON] without inserting a cassette and a card,
the demonstration starts. For normal use, set
this function to [OFF]. (
-61-
)
3: A cassette cannot be inserted.
• Has condensation occurred? Wait until the
• Has condensation occurred? Wait until the
condensation indication disappears.
4: Auto focus function does not work.
• Is manual focus mode selected? If auto focus
• Is manual focus mode selected? If auto focus
mode is selected, focus is automatically
adjusted.
adjusted.
• There are some recording subjects and
surroundings for which the auto focus does not
operate correctly. (
operate correctly. (
-72-
) If so, use the manual
focus mode to adjust the focus. (
-38-
)
• Is the MagicPix function set? When the
MagicPix function is working, focusing shifts
into the manual mode.
into the manual mode.
Indications
1: A sentence is displayed in red or yellow in
1: A sentence is displayed in red or yellow in
the screen center.
• Read the contents and respond to them. (
-63-
)
2: The time code becomes inaccurate.
0 The time code indication counter may not be
0 The time code indication counter may not be
constant in the reversed slow-motion playback,
but this is not a malfunction.
but this is not a malfunction.
3: The remaining tape time indication
disappears.
• The remaining tape time indication may
disappear temporarily during frame-by-frame
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
4: The remaining tape time Indication does not
match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be correctly displayed.
cannot be correctly displayed.
• In some cases, the remaining tape time
indication may show remaining tape time that is
2 to 3 minutes shorter than the actual
remaining tape time.
2 to 3 minutes shorter than the actual
remaining tape time.
5: A function indication such as mode
indication, remaining tape time indication,
or time cord indication is not shown.
or time cord indication is not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF],
indications other than the tape running
condition, warning, and date indications
disappear.
condition, warning, and date indications
disappear.
Playback (Sound)
1: Sound is not played back from the built-in
1: Sound is not played back from the built-in
speaker of the Camcorder or the
headphones.
headphones.
0 Is the volume too low? During playback, push
the [
s
/VOL
r] lever to display the volume
indication and adjust it. (
-40-
)
2: Different sounds are reproduced at the
same time.
• Have you set [SETUP] >> [12bit AUDIO] >>
[MIX]? If you set [AUDIO REC] >> [12bit] and
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (
-47-
)
LSQT0973ENG.book 66 ページ 2006年1月30日 月曜日 午前11時40分