Sharp VL-NZ10S 用户手册
Advanced Features
60
Editing
Available mode:
TAPE-VCR
Video editing lets you refine your videos by
removing unwanted sequences from your tape,
or transposing one sequence with another.
This camcorder lets you monitor the source
program on the built-in LCD monitor without
having to connect it to an external TV or video
monitor.
removing unwanted sequences from your tape,
or transposing one sequence with another.
This camcorder lets you monitor the source
program on the built-in LCD monitor without
having to connect it to an external TV or video
monitor.
Connect the camcorder to a VCR with the
supplied audio/video/S-video cable, as shown.
supplied audio/video/S-video cable, as shown.
Cutting Unwanted Sequences
1
Play back the tape to be edited on the
camcorder, and locate the beginning
and end of the sequence you wish to
cut. Write down the time code reading at
the beginning and end of that sequence
(see page 59). Then, rewind the tape to
before the beginning of the portion that
you wish to keep.
camcorder, and locate the beginning
and end of the sequence you wish to
cut. Write down the time code reading at
the beginning and end of that sequence
(see page 59). Then, rewind the tape to
before the beginning of the portion that
you wish to keep.
2
Load a video cassette into the recording
VCR.
VCR.
3
Press m on the camcorder to begin
playback, then press the Record button
on the VCR to begin recording.
playback, then press the Record button
on the VCR to begin recording.
4
Press the Pause/Still button on the VCR
to pause recording when the source
tape reaches the beginning of the
sequence to be cut.
to pause recording when the source
tape reaches the beginning of the
sequence to be cut.
5
Press the Pause/Still (or Record) button
on the VCR to resume recording when
the source tape reaches the end of the
sequence to be cut.
on the VCR to resume recording when
the source tape reaches the end of the
sequence to be cut.
POWER
TV/VCR SET UP
CHANNEL
REC
PLAY
STOP/
EJECT
EJECT
PAUSE
/STILL
/STILL
:
To stop editing
Press l on the camcorder and press the Stop
button on the VCR.
button on the VCR.
Notes:
• Some of the transitions between edited
• Some of the transitions between edited
sequences may be slightly off.
• There may be picture noise during video search
or still playback. This does not imply a defect in
the camcorder.
the camcorder.
• The time code display will be recorded along
with the edited sequences if the TC OUT item is
set to “ON”. Set to “OFF” before editing (see
page 59).
set to “ON”. Set to “OFF” before editing (see
page 59).
Notes:
• If your VCR has a 21-pin Euro-SCART connector,
• If your VCR has a 21-pin Euro-SCART connector,
use the RCA/21-pin Euro-SCART conversion
connector (QSOCZ0033TAZZ).
connector (QSOCZ0033TAZZ).
0
VIDEO
AUDIO
(L/MONO)
AUDIO
(R)
• See page 2 for how to open the jack cover.
• If your VCR has only one audio input jack, use
• If your VCR has only one audio input jack, use
the white plug for the audio connection on the
VCR.
VCR.
• If your VCR has an S-video input socket, you do
not need to connect the yellow video plug.
To AVLS terminal
Recording
Black: To S-video input socket
Yellow: To video input jack
White: To audio input (L) jack
Red: To audio input (R) jack
Yellow: To video input jack
White: To audio input (L) jack
Red: To audio input (R) jack
Audio/video/S-video cable (supplied)
Playback
The arrow shows the signal flow.
21-pin Euro-SCART on VCR
RCA/21-pin Euro-SCART
conversion connector
(QSOCZ0033TAZZ)
conversion connector
(QSOCZ0033TAZZ)
Video
Audio R
Audio L
Audio L