Sony HVR-Z1 用户手册
10
PREPARING CAMCORDER & HOUSING
INSTALLING ACCESSORIES
The PHENOM as been equipped with mounting holes and
railing systems to accommodate for a variety of accessories.
Locations for a few of these accessories have been
designated for your convenience. However, these locations
can be used for other accessories. Some accessories like
the monitor or video lights require to be connected to the
housing. Accessory connector ports (one on the right side
and two on the left side) are available for this purpose.
The PHENOM as been equipped with mounting holes and
railing systems to accommodate for a variety of accessories.
Locations for a few of these accessories have been
designated for your convenience. However, these locations
can be used for other accessories. Some accessories like
the monitor or video lights require to be connected to the
housing. Accessory connector ports (one on the right side
and two on the left side) are available for this purpose.
Achieving neutral buoyancy and balance
Adding accessories to the housing may make it heavier or off
balance in the water. Removable ballasts have been added
to the bottom of the housing for this purpose.
Adding accessories to the housing may make it heavier or off
balance in the water. Removable ballasts have been added
to the bottom of the housing for this purpose.
To make the necessary weight adjustments.
1. Submerge the housing with the added accessories
into the water so you get an idea of what and where to
remove weight.
2. Using the allen key supplied, start removing or
relocating the ballasts from the right or the left channels
as illustrated.
1. Submerge the housing with the added accessories
into the water so you get an idea of what and where to
remove weight.
2. Using the allen key supplied, start removing or
relocating the ballasts from the right or the left channels
as illustrated.
WATER ENTRY
1. Always turn housing to its ON position before entering
water. To turn it ON, use the right grip trigger button. This is
confirmed by the CAM. indicator light turning on steady
green. The camcorder viewfinder will also turn ON.
Doing step 1 will activate the built-in moisture alarm sensor
located in the bottom of the housing.
IMPORTANT
1. Always turn housing to its ON position before entering
water. To turn it ON, use the right grip trigger button. This is
confirmed by the CAM. indicator light turning on steady
green. The camcorder viewfinder will also turn ON.
Doing step 1 will activate the built-in moisture alarm sensor
located in the bottom of the housing.
IMPORTANT
All indicator lights will start flashing RED if water
leakage occurs inside the housing. Remove from water
as soon as possible, take the camcorder out of the
housing and inspect all seals and the inside of the
housing. ALWAYS REMEMBER DIVER SAFETY FIRST.
2. Lower the housing just below the water surface in level
position and hold for one minute to confirm there is no
leakage in the housing.
Never leap into the water while holding the housing. Always
have the housing handed to you or lowered down once you
are in the water.
3. Point the lens of the housing upwards and shake off any
air bubbles. It may also be necessary to gently wipe the lens
with your finger to remove bubbles.
as soon as possible, take the camcorder out of the
housing and inspect all seals and the inside of the
housing. ALWAYS REMEMBER DIVER SAFETY FIRST.
2. Lower the housing just below the water surface in level
position and hold for one minute to confirm there is no
leakage in the housing.
Never leap into the water while holding the housing. Always
have the housing handed to you or lowered down once you
are in the water.
3. Point the lens of the housing upwards and shake off any
air bubbles. It may also be necessary to gently wipe the lens
with your finger to remove bubbles.
Video lights
Video lights
"T" bracket
Monitor bracket
Carry handle
Accessory
connector port
connector port
Allen key (supplied)
Ballast
Right Grip
Trigger Button
CAM
ZO
OM
-W
ZO
OM
-T
W
B
FO
CU
S
VCR
PWR SAVE