Honeywell HB73 产品宣传页

READ AND KEEP THIS

OPERATION MANUAL

•

 D

a y

  ( C

o l o r   M o d

e )

 

•

 N

ig

h

t 

(B

/

W

 M

od

e)a

t 

Lo

w-

Li

gh

t 

c

o

n

d

it

io

n

• 1/3" Sony Super HAD CCD
• High Resolution: 550 TV Lines
• Auto White Balance
• AGC, BLC, Flickerless On/Off
• 3.8 - 9.5 mm DC Vari-focal Auto Iris Lens
• Super Digital Noise Reduction (SDNR)
• Electronic Sensitivity-up(DSS) On/Off
• Weatherproof Housing
• IP65

Do not install the camera in extreme
temperature conditions.
Do use the camera under conditions where 
temperatures are within -10°C to 45°C. 
Be especially careful with ventilation under 
high temperatures.

Do not install the camera under unstable 
lighting conditions.
Severe lighting change or flicker can cause 
the camera to work improperly.

Do not drop the camera or subject 
to physical shock.
It can cause malfunctions to occur.

Never point the camera into strong 
light or the sun.
It can damage CCD.

NTSC : 525 Lines                        PAL : 625 Lines 

2 : 1 Interlace

 15.734kHz                                 15.625kHz

 59.94Hz                                       50Hz  

1/3 inch SONY Super HAD CCD

  410K                                          470K

50dB Min. (AGC Off)

550 TV Lines

1.0 Vp-p (75 Ohms, composite)

Vari-focal Lens (F=1.2, f=3.8~9.5mm)

Manual
Internal

0.3 Lux (color)/ 0.008 Lux (DSS On) / 0 Lux (IR LED On)

 1/60 ~ 120,000 Sec.               1 /50 ~ 120,000 Sec.

Auto

On / Off Selectable

On / Off (Max 32 times)

On / Off (2 x)

AUTO

Power (Red Jack), Video (Yellow Jack)

-10°C ~ 45°C
-20°C ~ 65°C

12VDC (10V~15V), 0.3A/3.6W (Max)

75 x 78 x 150mm

Approx. 800g

P/N:3810-0054S

Rev 0 03

/18

      As surroundings darken, it switches 

automatically from color to black-and-white 

mode to enhance sensitivity.

※

Operation Manual

Bracket Mounting Screws

L-Wrench

Sun Visor Fastener

Video
(Yellow)

Power- 12VDC
(Red)

• The wire is polarized.

• Use 12VDC      power source.

WARNING - Changes or modifications not expressly approved by the 

manufacturer could void the user's authority to operate the equipment.
CAUTION - When this camera is installed near equipment, like a wireless 

communication device that emits a strong electromagnetic field, some 

irregularity such as noise on the monitor screen may happen.

This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions : (1)This device may not cause harmful interference, 

and (2) this device must accept any interference received, including interference 

that may cause undesired operation. 
This equipment has been tested and found to comply with the limits for a 

Class A digital device, pursuant to Part 15 of the FCC Rules.These limits are 

designed to provide reasonable protection against harmful interference in a 

commercial environment. 

This equipment generates, uses, and can radiate radio frequency energy and, 

if not installed and use in accordance with the instructions, may cause harmful 

interference to radio communications. Operation of this equipment in a 

residential area is likely to cause interference, in which case the user will be 

required to correct the interference at his own expense. 

• 

Check the power source for the monitor and 

    camera and ensure that the voltage and polarity

    are correct.

• 

Check if you have connected the camera to a proper 

    power source and If there is no problem with the power, 

    turn the unit off immediately and seek assistance from 

    our Customer Service department.

• 

Check if the camera is pointed toward the sun or a 

    fluorescent lamp.

• 

Adjust the angle or location of the camera if too much 

    light is coming into the screen.

• 

Check if the lens is stained. If dirty, clean the lens with 

    a soft, clean cloth.

• 

Adjust the Back Focus of the lens again.

If you have trouble operating your camera, refer to the following. 

 If the guidelines do not enable you to solve the problem, 

 contact an authorized technician.

Function Selection Switch: 
•BLC(Back Light Compensation) 

  ON/OFF

•AGC(Auto Gain Control) ON/OFF

•D/N(Day & Night) ON/OFF

•DSS(Digital Slow Shutter) ON/OFF

•D.Z(Digital Zoom) ON/OFF

•FLK(Flickerless) ON/OFF

Need Help?

Call 1.800.796.CCTV for sales, service and customer support.

www.honeywellvideo.com

     CAUTION : When AGC is off, 

      D/N does not work because the 

      D/N switching function is 

      dependent on the AGC level.

Service Monitor Connecter: 

Use service monitor connector

to set camera angle & focus

when installing.

Video Output

Power Input

1.0 Vp-p

12VDC(10V~15V), 0.3A(Max)

Yellow

Red

Used to adjust video output level of DC driven auto iris lens.

When the brightness control of the monitor does not operate correctly,

you can optimize the picture picture by controlling the DC level of camera.

Used to adjust zoom magnification by 

turning.

Used to provide for accurate focusing 

of object within the lens field of view.

850nm / 30°(18EA)