Honeywell HCD544X 产品宣传页
Document 800-03503 – Rev C – 03/09
HCD544/HCD544X/HCD545X Camera
Quick Install Guide
Quick Install Guide
Document 800-03503 — Rev C — 03/09
Important Safety Instructions
•
Read and keep these instructions.
•
Heed all warnings.
•
Follow all instructions.
•
Do not use this apparatus near water.
•
Clean only with dry cloth.
•
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
instructions.
•
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
apparatus (including amplifiers) that produce heat.
•
Use only with the bracket or mounting system specified by the manufacturer, or sold
with the apparatus.
with the apparatus.
•
Refer all servicing to qualified service personnel.
Installation
The HCD544 Series camera is designed for general surveillance applications and is
ideally suited for low-light indoor environments.
ideally suited for low-light indoor environments.
Installing the Lens
The HCD544 Series camera is factory configured for a CS-mount lens. Screw the lens
(customer supplied) into the front of the camera body. An IR corrected Day/Night lens
is recommended for this camera.
(customer supplied) into the front of the camera body. An IR corrected Day/Night lens
is recommended for this camera.
Figure 1
Lens Installation
Connecting the Camera
Note
Check the power source from the external power supply before applying
power to the camera.
power to the camera.
1.
Connect the VIDEO connector on the rear of the camera to the video-in connector
on your monitor or video recorder.
on your monitor or video recorder.
2.
HCD544/HCD544X models: Connect the camera to a power supply appropriate
for your installation (12 VDC or 24 VAC).
for your installation (12 VDC or 24 VAC).
Plug the power supply into an appropriate power source.
3.
HCD545X model: Connect the power cord to the power cord socket.
Plug the power cord plug into an electrical outlet of AC230V, 50 Hz. Accepted
voltage range is 207 VAC~253 VAC.
voltage range is 207 VAC~253 VAC.
The power LED illuminates to show that the camera is receiving power.
Figure 2
Video Connections
Connecting LAMP Contact
The HCD544 camera is equipped with LAMP and GND external contact terminals (see
). When the LAMP terminal is connected to the GND terminal, the camera is
forced into night mode (see
). It stays in night mode until the LAMP
terminal is disconnected from the GND terminal.
Adjusting the Back Focus
To adjust the back focus, aim the camera towards a darker area, or use a Neutral
Density lens filter. For best results, there should be a minimum of 15 ft (4.5 m)
between the camera and the target focal area.
Density lens filter. For best results, there should be a minimum of 15 ft (4.5 m)
between the camera and the target focal area.
1.
Loosen the setscrews (see
) with a Phillips screwdriver.
2.
Set the Zoom lens adjustment to Wide and the Focus lens adjustment to Near.
3.
Adjust the back focus ring to focus the picture.
4.
Retighten the setscrews.
Mounting the Camera
There are mounting points on the top and bottom of the camera (see
) to
mount the camera on a bracket or tripod. Use standard sized mounting bolts to install
the camera to a mounting bracket.
the camera to a mounting bracket.
Caution
Follow local installation codes for proper mounting bracket support
capability.
capability.
Figure 3
Camera Mounting.
Making Final Adjustments
Adjust the focus in your field of view until you see a clear image. If necessary, adjust
the brightness using the OSD menu controls (see
the brightness using the OSD menu controls (see
DC/BRIGHTNESS
or
).
Confirm the exposure on the monitor screen.
Programming
OSD Menu Controls
Figure 4
Camera Controller
OSD Menu Structure
The HCD544 Series camera menu system consists of one main SETUP menu for easy
camera programming.
camera programming.
Figure 5
Menu Structure
3 4
1 2
Pin
Function
1
CTRL -
2
CTRL +
3
DRV +
4
DRV -
Setscrews (x2)
DC Lens Pin Definitions
Power LED
AC24V/DC12V terminal block
LAMP terminal
GND terminal
GND terminal
HCD544/HCD544X
HCD545X
Power LED
LAMP terminal
GND terminal
230 VAC
power supply
power supply
Mounting point
Top view shown
Navigating through the menus
Press this control To do this …
ENTER
Press and hold two seconds to enter
SETUP menu. Press to enter a
screen or select a menu option.
SETUP menu. Press to enter a
screen or select a menu option.
UP, DOWN
(!
(!
,
")
Move vertically between menus and
options. Increase/decrease a value.
options. Increase/decrease a value.
LEFT, RIGHT
(#
(#
,
$)
Move horizontally between menus
and options.
and options.
..
Indicates submenus. Select the
menu, then press ENTER.
menu, then press ENTER.
RETURN (on OSD
submenus)
submenus)
Exit the submenu. Select RETURN,
then press ENTER.
then press ENTER.
Camera OSD control
(4 position plus
center press (ENTER)
(4 position plus
center press (ENTER)
Note
Menu display turns off automatically after five minutes of
no activity. Your changes will be saved.
<<SETUP MENU>>
LENS
DC
SHUTTER
MANUAL ..
WHITE BAL.
AWC ..
BACKLIGHT
ON
AGC
30dB
SPECIAL ..
EXIT MENU ..
EXIT MENU ..
1
2
3
4
5
6
7
2
3
4
5
6
7
LENS
DC .., MANUAL
SHUTTER
WHITE BAL
BACKLIGHT
AGC
SPECIAL ..
FLK, MANUAL .., ESC
ATW .., AWC (PUSH/LOCK), AWC
AUTO ..,USER .., MANUAL ..
AUTO ..,USER .., MANUAL ..
ON, OFF
18 dB~30 dB, OFF
See
Main Menu
Menu Options
Submenu
See
for a description of the
submenus and menu options.
submenus and menu options.