Revolabs 01-HDEXEC-NM 用户手册
- 31 -
4. LED display — visual status for mute, un-mute, and pairing.
5. TA4M connector — connects to Countryman microphone cable.
5. TA4M connector — connects to Countryman microphone cable.
To use the HD Wireless Adapter for Countryman Microphone:
20. Remove the Microphone Adapter from the Charger Base.
The adapter turns on and mutes automatically when removed from Charger Base (flashing RED
LED). The Microphone Adapter is attached to a Countryman Microphone with the specific cable
designed for Revolabs. The HD Wireless Adapter for Countryman microphone supplies the
necessary phantom power specifically for the Countryman microphone.
LED). The Microphone Adapter is attached to a Countryman Microphone with the specific cable
designed for Revolabs. The HD Wireless Adapter for Countryman microphone supplies the
necessary phantom power specifically for the Countryman microphone.
21. To turn the Adapter off, return the microphone unit to the Charger Base or press and hold the
Mute button for ~10 seconds until the LED turns solid RED then release button.
Important: Always remove the microphone from the Adapter and separate the parts before
returning the Adapter to the Charger Base.
returning the Adapter to the Charger Base.
If the Adapter is moved too far from the Base Station (~300 feet or 91 meters) the connection will be
dropped (LED flashes all colors) and the audio will mute. After 15 seconds the microphone will beep
5 times, and will continue beeping every 30 seconds to indicate that it is out of range.
dropped (LED flashes all colors) and the audio will mute. After 15 seconds the microphone will beep
5 times, and will continue beeping every 30 seconds to indicate that it is out of range.
Move the Countryman Adapter closer to the Base Station and the connection will automatically be re-
established to its original state, and the beeping will cease. If not, the Countryman Adapter will
continue beeping until it turns off in about 15 minutes.
established to its original state, and the beeping will cease. If not, the Countryman Adapter will
continue beeping until it turns off in about 15 minutes.
Pairing Wireless Microphones to Base Station
Pairing creates a link between the HD wireless microphone and the Base Station, with a unique
electronic serial number. When the microphone and Base Station have been previously paired, the
mic will automatically try to connect to the same Base Station whenever it is lifted from the Charger
Base.
Note: Microphones in new systems must be paired to the Base Station with each microphone
assigned to a unique channel on the base unit.
assigned to a unique channel on the base unit.
Remember, microphones are by default muted (flashing RED LED) when they are removed from the
Charger Base and the Mute button needs to be pressed to make it “live” (flashing GREEN LED).
Charger Base and the Mute button needs to be pressed to make it “live” (flashing GREEN LED).
A microphone that is not paired will be indicated by a cycling RED-GREEN LED pattern. A Base
Station channel that is not paired to a microphone will not show any activity on the channel LED
(make sure unit is first powered on by observing GREEN backlit front panel display).
Station channel that is not paired to a microphone will not show any activity on the channel LED
(make sure unit is first powered on by observing GREEN backlit front panel display).
When channels are paired, both microphone and channel LEDs will flash RED as microphones are
removed from the Charger Base and flash GREEN when un-muted. Remember that only one
microphone can be paired to any single Base Station channel.
removed from the Charger Base and flash GREEN when un-muted. Remember that only one
microphone can be paired to any single Base Station channel.
“Express Pair” is a tool in the HD Control Panel Software that can be used to pair all the microphones
in a Charger Base to a Base Station at the same time. (See: Tools – Express Pair)
in a Charger Base to a Base Station at the same time. (See: Tools – Express Pair)