Wayne-Dalton 2411 用户手册
PG. 3
DIM Y
HEADER TO
SHAFT
CENTERLINE
HEADER TO
SHAFT
CENTERLINE
MINIMUM
HEADROOM
REQUIRED
(REFER TO
(REFER TO
ABOVE CHART)
8” for 2” TRACK
12” for 3” TRACK
12” for 3” TRACK
EXTEND JAMBS TO OPENING HEIGHT
plus
DIM Y
plus 1 1/2” (MINIMUM LENGTH)
TORSION SHAFTS REQUIRE 10” OF
SIDEROOM FOR SOLID SHAFTS and 5”
OF SIDEROOM FOR TUBULAR
SHAFTS
NOTE: HEADROOM CAN BE REDUCED 2-1/2” BY
USING THE QUICK CLOSING TOP FIXTURE OR BY
SHORTENING THE VERTICAL TRACKS BY
3” MAX.
SIDEROOM REQUIREMENTS
2 inch TRACK
3 inch TRACK
PRECAST WALL WITH
CORNER ANGLE
3” TRACK
PRECAST WALL WITHOUT
CORNER ANGLE
3” TRACK
STEEL JAMBS
3” TRACK
WOOD JAMBS
3” TRACK
STEEL JAMBS
2” TRACK
PRECAST WALL WITH
CORNER ANGLE
2” TRACK
PRECAST WALL WITHOUT
CORNER ANGLE
2” TRACK
WOOD JAMBS
2” TRACK
1” OVERLAP
1”
1/2”- 5/8”
4”
1” OVERLAP
1”
1/2”- 5/8”
4”
1”
1/2”- 5/8”
4”
FLUSH
1”
4”
4 3/4”
5/16 X 1”
DRILLING /
TAPPING
SCREW
3/8 X 3” MIN.
SLEEVE
ANCHOR
OPTIONAL
MOUNTING
BRACKET
5”
OPTIONAL
MOUNTING
BRACKET
3/8 X 3” MIN.
SLEEVE
ANCHOR
5/16 X 1”
DRILLING /
TAPPING
SCREW
2” X 6” JAMB
I S
RECOMENDED
1/2”- 5/8”
2 1/2” MIN.
SIDE ROOM
1” OVERLAP
1 1/2”
1/2”- 5/8”
3 1/2”
1” OVERLAP
1 1/2”
1/2”- 5/8”
3 1/2”
1” OVERLAP
1 1/2”
1/2”- 5/8”
3 1/2”
FLUSH
1 1/2”
3 1/2”
4 3/4”
5/16 X 1”
DRILLING /
TAPPING
SCREW
3/8 X 3” MIN.
SLEEVE
ANCHOR
OPTIONAL
MOUNTING
BRACKET
4 3/4”
OPTIONAL
MOUNTING
BRACKET
3/8 X 3” MIN.
SLEEVE
ANCHOR
5/16 X 1”
DRILLING /
TAPPING
SCREW
2” X 6” JAMB
I S
RECOMENDED
1/2”- 5/8”
2 1/2” MIN.
SIDE ROOM
2 1/2” MIN.
SIDE ROOM
3 1/2” MIN.
SIDE ROOM
5” MIN.
SIDE ROOM
3” MIN.
SIDE ROOM
3” MIN.
SIDE ROOM
3” MIN.
SIDE ROOM
5/16 X 1 5/8”
LAG SCREW
LAG SCREW
5/16 X 1 5/8”
LAG SCREW
LAG SCREW
1” OVERLAP
(2) 3/8” x 1-1/4” Bolts To
Secure Bracket To Angle
Heavy Perforated Angle
(1-5/8 x 2-3/8” x 11 GA.)
Center Spring Bracket
Girt
(2) 3/8” x 1-1/4” Bolts & Nuts
Top & Bottom
Girt
“Y”
(
<
7 ft.)
(2) 3/8” x 1-1/4” Bolts To
Secure Bracket To Angle
Heavy Perforated Angle
(1-5/8 x 2-3/8” x 11 GA.)
Center Spring Bracket
(2) 3/8” x 1-1/4” Bolts & Nuts
Top & Bottom
Girt
Girt
Space Center Brackets 12” -
14” Apart On Applications
Requiring Couplers
(2) 3/8” x 1-1/4” Bolts To
Secure Bracket To Angle
Heavy Perforated Angle
(1-5/8 x 2-3/8” x 11 GA.)
Center Spring Bracket
(2) 3/8” x 1-1/4” Bolts & Nuts
Top & Bottom
Girt
Girt
Space Center Brackets 12” -
14” Apart On Applications
Requiring Couplers
Bolt “Z” Shaped Assembly Using
(4) 3/8” x 1-1/4” Bolts And Nuts
Fig. N-2
Fig. N-3
Fig. N-4
Steel Spring Pad Applications
Contact Manufacturer For Applications Other Than What Is Listed Below
NOTE:
These Spring Mounting Techniques Are
Not Supported For 800-32, 6375-164, 1100-18,
1350-28, & 800-120 Drums. These Instructions
Are Also Not Applicable For 5750-120 Drums
With 72” Or More High-Lift
1350-28, & 800-120 Drums. These Instructions
Are Also Not Applicable For 5750-120 Drums
With 72” Or More High-Lift
NOTE:
Do Not Bolt (2) 3-3/4” Torsion Springs to
One Center Bracket
Maximum Door Size 9’ x 9’ (Maximum Door Weight 210 lb.): Cut perforated angle (1-5/8 x 2-3/8” x 11 GA.)
to Dim “Y”. Thru-bolt top and bottom of angle to each girt using (4) 3/8” x 1-1/4” bolts and nuts. Thru-
bolt center bracket to perforated angle using (2) 3/8 x 1-1/4” bolts and nuts (See Fig. N-2).
to Dim “Y”. Thru-bolt top and bottom of angle to each girt using (4) 3/8” x 1-1/4” bolts and nuts. Thru-
bolt center bracket to perforated angle using (2) 3/8 x 1-1/4” bolts and nuts (See Fig. N-2).
Maximum Door Size 14’ x 12’ (Maximum Door Weight 400 lb.): Cut (2) perforated angle (1-5/8 x 2-3/8” x
11 GA.) to Dim “Y”. Thru-bolt top and bottom of each angle to each girt using (4) 3/8” x 1-1/4” bolts and
nuts. Thru-bolt each center bracket to perforated angle using (2) 3/8 x 1-1/4” bolts and nuts (See Fig. N-3).
11 GA.) to Dim “Y”. Thru-bolt top and bottom of each angle to each girt using (4) 3/8” x 1-1/4” bolts and
nuts. Thru-bolt each center bracket to perforated angle using (2) 3/8 x 1-1/4” bolts and nuts (See Fig. N-3).
Maximum Door Size 14’-2” x 12’-1” (Maximum Door Weight 800 lb.): Cut (2) pieces of perforated angle
(1-5/8 x 2-3/8” x 11 GA.) to Dim “Y” and (2) more pieces at Dim “Y” minus 3. Bolt the angles together
into a “Z” shape using (4) 3/8” x 1-1/4” bolts and nuts. Thru-bolt top and bottom of each “Z” shaped angle
to each girt using (4) 3/8” x 1-1/4” bolts and nuts. Thru-bolt each center bracket to perforated angle
assembly using (2) 3/8 x 1-1/4” bolts and nuts (See Fig. N-4).
(1-5/8 x 2-3/8” x 11 GA.) to Dim “Y” and (2) more pieces at Dim “Y” minus 3. Bolt the angles together
into a “Z” shape using (4) 3/8” x 1-1/4” bolts and nuts. Thru-bolt top and bottom of each “Z” shaped angle
to each girt using (4) 3/8” x 1-1/4” bolts and nuts. Thru-bolt each center bracket to perforated angle
assembly using (2) 3/8 x 1-1/4” bolts and nuts (See Fig. N-4).
NOTE: Do NOT Bolt (2) 3-3/4” Torsion Springs To ONE Center Bracket
PG. 14
NOTE:
Maximum Spacing For Dimension “Y” is
84 in. (7 ft.) These Instructions Are Not Appli-
cable For A Span Greater Than 84 in.
cable For A Span Greater Than 84 in.
“Y”
(
<
7 ft.)
“Y”
(
<
7 ft.)