Regency P42-NG4 用户手册

Regency

®

 P42-4 Zero Clearance Direct Vent Gas Fireplace

14) Under no circumstances should any solid 

fuels (wood, paper, cardboard, coal, etc.) 
be used in this appliance.

15) The appliance area must be kept clear and 

free of combustible materials, (gases and 
other fl ammable vapours and liquids).

1)  Locate appliance, refer to the following 

sections: 

 a) 

Locating 

Your 

Gas 

Fireplace

 b) 

Clearances

 c) 

Mantels

 d) 

Mantels 

Legs 

Clearance

 e) 

Framing 

and 

Finishing

2)  Assemble Top Facing Support and Side 

Nailing Strips, see the "Top Assembly 
& Nailing Strips" section. NOTE: must 
be done before installing unit into 
fi replace.

3)  Install venting, refer to the "Venting" 

section.

4)  Make gas and electrical connections. Test 

the pilot. Must be as per diagram. See the 
"Pilot Adjustment" section. 

5)  Test Gas Pressure. Refer to the "Gas Pipe 

Pressure Testing" section.

6)  Install standard and optional features. 

 

Refer to the following sections where 
applicable: 

 
 a. 

Brick 

Panels

 

b. Log Set

 

c. Standard Flush Door

 d. 

Flush 

Louvers

 

e. Double Screen Door

 

f.  Bay Door

 g. 

Bay 

Louvers

 h. 

Full 

Screen 

Front

 

i.  Remote Control

 

j.  Wall Switch

 k. 

Wall 

Thermostat

11) Final check.

Before leaving this unit with the customer, 
the installer must ensure that the appliance is 
fi ring correctly and operation fully explained 
to customer.

Emissions from burning  wood or gas could 
contain chemicals known to the State of 
California to  cause cancer, birth defects or 
other reproductive harm.

The P42-NG/P42-LP Direct Vent Fireplace must 
be installed in accordance with these instructions. 
Carefully read all the instructions in this manual 
fi rst. Consult the "authority having jurisdiction" to 
determine the need for a permit prior to starting 
the installation. It is the responsibility of the 
installer to ensure this fi replace is installed in 
compliance with manufacturers instructions and 
all applicable codes.

Safe installation and operation of this appliance 
requires common sense, however, we are 
required by the Canadian Safety Standards 
and ANSI Standards to make you aware of 
the following:

1)  The appliance installation must conform 

with local codes or, in the absence of local 
codes, with the current Canadian or National 
Gas Codes, CAN1-B149 or ANSI Z223.1 
Installation Codes.

2)  The appliance when installed, must be 

electrically grounded in accordance with 
local codes, or in the absence of local codes 
with the current National Electrical Code, 
ANSI/NFPA 70 or CSA C22.1 Canadian 
Electrical Code.

3)  See general construction and assembly 

instructions. The appliance and vent should 
be enclosed.

4)  This appliance must be connected to the 

specifi ed vent and termination cap to the 
outside of the building envelope. Never vent 
to another room or inside a building. Make 
sure that the vent is fi tted as per Venting 
instructions.

5)  Inspect the venting system annually for 

blockage and any signs of deterioration.   

6)  Venting terminals shall not be recessed into 

a wall or siding.

7)  Any safety glass removed for servicing 

must be replaced prior to operating the 
appliance.

8)  To prevent injury, do not allow anyone who 

is unfamiliar with the operation to use the 
fi replace.

9)  Wear gloves and safety glasses for protection 

while doing required maintenance.

10) Be aware of electrical wiring locations in 

walls and ceilings when cutting holes for 
termination.

11) Under no circumstances should this 

appliance be modifi ed. Parts that have to be 
removed for servicing should be replaced 
prior to operating this appliance.

12) Installation and any repairs to this appliance 

should be done by an authorized service 
person. A professional service person should 
be called to inspect this appliance annually. 
Make it a practice to have all of your gas 
appliances checked annually.

13) Do not slam shut or strike the glass door.