Haier HSU-12HEG03/R2(DB) 用户手册

Operation

Press FAN button. For each press, fan speed 

follows:

Remote controller:

Press

button

Every time the button is pressed, temp.setting
increase 1

o

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

o

C,if kept depressed, it will 

decrease  rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.

1. Unit start

 Press ON/OFF on the remote controller, unit starts.

Remote controller

1.Status display of air flow

When restart after remote turning off, the remote 

         memorize the previous 

Move the vertical blade by a knob on air

to adjust left and right direction referring to Fig.

2.Left and right air flow adjustment(manual)

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur 

adjusted to left or 

It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY

otherwise, condensate water might occur.

conditioner

at air outlet if all vertical louvers are 

right.

mode ,

controller will automatically

Note:

set swing position.

changes as

Operation

Mode

Remote

Controller

Note

In DRY mode , when room temperature becomes lower
than temp.setting+2

o

C, unit will run intermittently at LOW 

speed regardless of FAN setting. 

Under the mode of auto operation, air conditioner will

automatically select Cool or Heat operation according to

room temperature. When FAN is set to AUTO the air 

conditioner automatically adjusts the fan speed according
to room temperature.

In FAN operation mode , the unit will not operate in COOL or
HEAT mode  but only in  FAN mode, AUTO is not available in

FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.  

Emergency Operation:

Use this operation only when the remote controller is defective 
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation. 
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in 
the following modes:

    Room
temperature

Designated
temperature

Timer
mode

Fan

speed

Operation

mode

  Above 23

o

C

  Below 23

o

C

 

23

o

C

 26

o

C

No

AUTO

AUTO

COOL

HEAT

No

It is impossible to change the settings of temp. and fan speed,It 
is also not possible to operate in timer or dry mode.

temperature is below 16

o

C, do not use it in the 

Test operation:

Use this switch in the test operation when the room

normal operation.

 your finger from the switch: the cooling

Continue to press the test operation 

switch for more than 5 seconds . After

 you hear the "Pi" sound twice, release

Test ope ration switch is the same as emergency switch.

operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor

unit will run in high speed.

LOW

MED

HI

AUTO

2.

 

Select operation mode

COOL button:Cooling mode
HEAT button: Heating mode
DRY button: Dehumidify mode

Display 

circulated

DRY

COOL

AUTO

HEAT

FAN

In HEAT mode, warm air will blow out after a short 
period of the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically 
adjusts the fan speed according to room temperature.

test operation

 switch

Pi

Pi

Pi

emergency

operation switch

'

2

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

(Auto swing)

cooling mode:from pos.1 to pos.4 and pos.6
heating mode:from pos.5 to pos.1 and pos.6