Goodman Mfg CPC/CPH 用户手册
3
T
HIS
UNIT
MUST
NOT
BE
USED
AS
A
“
CONSTRUCTION
HEATER
”
DURING
THE
FINISHING
PHASES
OF
CONSTRUCTION
ON
A
NEW
STRUCTURE
. T
HIS
TYPE
OF
USE
MAY
RESULT
IN
PREMATURE
FAILURE
OF
THE
UNIT
DUE
TO
EXTREMELY
LOW
RETURN
AIR
TEMPERATURES
AND
EXPOSURE
TO
CORROSIVE
OR
VERY
DIRTY
ATMOSPHERES
.
WARNING
HIGH VOLTAGE!
D
ISCONNECT
ALL
POWER
BEFORE
SERVICING
OR
INSTALLING
THIS
UNIT
. M
ULTIPLE
POWER
SOURCES
MAY
BE
PRESENT
. F
AILURE
TO
DO
SO
MAY
CAUSE
PROPERTY
DAMAGE
,
PERSONAL
INJURY
OR
DEATH
.
WARNING
WARNING
T
O PREVENT THE RISK OF PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH,
DO NOT STORE COMBUSTIBLE MATERIALS OR USE GASOLINE OR OTHER
FLAMMABLE LIQUIDS OR VAPORS IN THE VICINITY OF THIS APPLIANCE.
FLAMMABLE LIQUIDS OR VAPORS IN THE VICINITY OF THIS APPLIANCE.
GENERAL INFORMATION
T
O
PREVENT
PROPERTY
DAMAGE
PERSONAL
INJURY
OR
DEATH
,
DUE
TO
FIRE
,
EXPLOSIONS
,
SMOKE
,
SOOT
,
CONDENSATION
,
ELECTRIC
SHOCK
OR
CARBON
MONOXIDE
,
THIS
UNIT
MUST
BE
PROPERLY
INSTALLED
,
REPAIRED
,
OPERATED
,
AND
MAINTAINED
.
WARNING
This unit is approved for outdoor installation ONLY.
Rated performance is achieved after 72 hours of opera-
tion. To assure that your unit operates safely and efficiently,
it must be installed, operated, and maintained in accor-
dance with these installation and operating instructions,
all local building codes and ordinances.
Rated performance is achieved after 72 hours of opera-
tion. To assure that your unit operates safely and efficiently,
it must be installed, operated, and maintained in accor-
dance with these installation and operating instructions,
all local building codes and ordinances.
EPA R
EGULATIONS
I
MPORTANT
: T
HE
U
NITED
S
TATES
E
NVIRONMENTAL
P
ROTECTION
A
GENCY
(EPA)
HAS
ISSUED
VARIOUS
REGULATIONS
REGARDING
THE
INTRODUCTION
AND
DISPOSAL
OF
REFRIGERANTS
IN
THIS
UNIT
. F
AILURE
TO
FOLLOW
THESE
REGULATIONS
MAY
HARM
THE
ENVIRONMENT
AND
CAN
LEAD
TO
THE
IMPOSITION
OF
SUBSTANTIAL
FINES
. B
ECAUSE
REGULATIONS
MAY
VARY
DUE
TO
PASSAGE
OF
NEW
LAWS
,
WE
SUGGEST
A
CERTIFIED
TECHNICIAN
PERFORM
ANY
WORK
DONE
ON
THIS
UNIT
. S
HOULD
YOU
HAVE
ANY
QUESTIONS
PLEASE
CONTACT
THE
LOCAL
OFFICE
OF
THE
EPA.
N
ATIONAL
C
ODES
This product is designed and manufactured to permit instal-
lation in accordance with National Codes. It is the installer’s
responsibility to install the product in accordance with Na-
tional Codes and/or prevailing local codes and regulations.
lation in accordance with National Codes. It is the installer’s
responsibility to install the product in accordance with Na-
tional Codes and/or prevailing local codes and regulations.
The heating and cooling capacities of the unit should be
greater than or equal to the design heating and cooling loads
of the area to be conditioned. The loads should be calculated
by an approved method or in accordance with ASHRAE Guide
or Manual J - Load Calculations published by the Air Condi-
tioning Contractors of America.
greater than or equal to the design heating and cooling loads
of the area to be conditioned. The loads should be calculated
by an approved method or in accordance with ASHRAE Guide
or Manual J - Load Calculations published by the Air Condi-
tioning Contractors of America.
Obtain from:
American National Standards Institute
1430 Broadway
New York, NY 10018
System design and installation should also, where applicable,
follow information presented in accepted industry guides such
as the ASHRAE Handbooks. The manufacturer assumes no
responsibility for equipment installed in violation of any code
or regulation. The mechanical installation of the packaged
roof top units consists of making final connections between
the unit and building services; supply and return duct con-
nections; and drain connections (if required). The internal
systems of the unit are completely factory-installed and tested
prior to shipment.
follow information presented in accepted industry guides such
as the ASHRAE Handbooks. The manufacturer assumes no
responsibility for equipment installed in violation of any code
or regulation. The mechanical installation of the packaged
roof top units consists of making final connections between
the unit and building services; supply and return duct con-
nections; and drain connections (if required). The internal
systems of the unit are completely factory-installed and tested
prior to shipment.
Units are generally installed on a steel roof mounting curb
assembly which has been shipped to the job site for installa-
tion on the roof structure prior to the arrival of the unit. The
model number shown on the unit’s identification plate identi-
fies the various components of the unit such as refrigeration
tonnage, heating input and voltage.
assembly which has been shipped to the job site for installa-
tion on the roof structure prior to the arrival of the unit. The
model number shown on the unit’s identification plate identi-
fies the various components of the unit such as refrigeration
tonnage, heating input and voltage.
Carefully inspect the unit for damage including damage to
the cabinetry. Any bolts or screws which may have loosened
in transit must be re-tightened. In the event of damage, the
receiver should:
1. Make notation on delivery receipt of any visible
damage to shipment or container.
2. Notify carrier promptly and request an inspection.
3. In case of concealed damage, carrier should be
3. In case of concealed damage, carrier should be
notified as soon as possible-preferably within 5 days.
4. File the claim with the following supporting documents:
a. Original Bill of Lading, certified copy, or indemnity
bond.
b. Original paid freight bill or indemnity in lieu thereof.
c. Original invoice or certified copy thereof, showing
c. Original invoice or certified copy thereof, showing
trade and other discounts or reductions.
d. Copy of the inspection report issued by carrier
representative at the time damage is reported to the
carrier. The carrier is responsible for making prompt
inspection of damage and for a thorough
investigation of each claim. The distributor or
manufacturer will not accept claims from dealers for
transportation damage.
carrier. The carrier is responsible for making prompt
inspection of damage and for a thorough
investigation of each claim. The distributor or
manufacturer will not accept claims from dealers for
transportation damage.