Crown Boiler BWC120 用户手册

VII Venting

WARNING

FAILURE TO VENT THIS BOILER IN ACCORDANCE WITH THESE INSTRUCTIONS COULD CAUSE 

FLUE GAS TO ENTER THE BUILDING RESULTING IN SEVERE PROPERTY DAMAGE, PERSONAL 

INJURY, OR DEATH:

* Do not attempt to vent this boiler with galvanized, PVC, or any other vent components not listed in Table 7.4.

* Do not attempt to mix components from different approved vent systems.

* Do not obtain combustion air from within the building. 

* Do not install a barometric damper or drafthood on this boiler.

A. Vent System Design

There are four basic ways to vent this boiler:

•  Horizontal (“Side Wall”) Concentric Venting - Vent system exits the building through an outside wall. 

Concentric venting consists of a “pipe within a pipe”. Flue gas exits the building through the inner pipe and 

combustion air is drawn into the boiler through the space between the inner and outer pipe.

•  Horizontal (“Side Wall”) Twin Pipe Venting - Vent system exits the building through an outside wall. 

Combustion air and flue gas are routed between the boiler and outdoors using separate pipes. 

•  Vertical Concentric Venting - Vent system exits the building through the roof. Concentric venting consists of a 

“pipe within a pipe”. Flue gas exits the building through the inner pipe and combustion air is drawn into the boiler 

through the space between the inner and outer pipe.

•  Vertical Twin Pipe Venting - Vent system exits the building through a roof. Combustion air and flue gas are 

routed between the boiler and outdoors using separate pipes. 

  All of these systems are considered “direct vent” because in all of them air for combustion is drawn directly from  

  the outdoors into the boiler. A description of all of these venting options are shown in Tables 7.1 and 7.9. For clarity,  

  these vent options are numbered from 1 to 6. One of the vent option columns in Tables 7.1 or 7.9 must match the  

  planned vent and air intake system exactly. In addition, observe the following guidelines:

1)   Approved vent systems - Use only one of the approved vent systems shown in Tables 7.4 or 7.5. These vent systems 

fall into two basic categories:

•  Concentric Vent System - The standard boiler is supplied with a concentric vent system having a maximum 

usable length of 25” (Figure 1.1). For longer runs, additional straight lengths and elbows are available from 

Crown. In some cases, larger diameter concentric pipe must be used. Each Crown concentric vent component 

consists of an inner pipe of polypropylene and the outer pipe of steel. Integral gaskets on each concentric fitting 

provide a gas tight seal.  A list of all Crown concentric vent components is shown in Table 7.4. 

     

   In this manual, concentric pipe sizes are called out in terms of the inner and outer pipe nominal diameters in 

millimeters. For example, “60/100mm” pipe consists of a 60mm exhaust pipe inside a 100mm diameter outer pipe.   

•  Twin Pipe Vent Systems - Approved vent systems are made of a special stainless steel alloy (AL29-4C) for 

protection against corrosive flue gas condensate. They are designed to provide a gas tight seal at all joints and 

seams so that flue gas does not enter the building. Each approved vent system has a unique method for installation 

- do not attempt to mix components from different vent systems. A list of approved twin pipe vent systems is 

shown in Table 7.5.  Note that a special vent collar (Crown PN 230510) is required if the boiler is to be vented 

with one of the approved stainless vent systems.   

11

CAUTION

 Moisture and ice may form on the surfaces around the vent termination. To prevent deterioration,  

   

surfaces should be in good repair (sealed, painted, etc.).