Lightolier 26096 用户手册
READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY
INSTRUCTION SHEETS BEFORE INSTALLING ANY TRACK ITEM
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
regulations. To assure full compliance with codes and regulations, check with your local electrical inspector
before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
regulations. To assure full compliance with codes and regulations, check with your local electrical inspector
before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:26096
0597
Page 1 of 3
GRID CEILING CANOPY KIT AND GRID CEILING MOUNTING CLIPS
FOR USE WITH PROSPEC
®
TRACK SYSTEMS ONLY
A. INSTRUCTIONS
1. Remove appropriate VERTICAL K.O.’s for T-BAR from OUTLET
BOX. DO NOT REMOVE ANY RECTANGULAR K.O.’s. (Fig. 1)
2. Attach a bare or green color insulated 12 AWG solid copper
GROUND WIRE approximately 8” long to the OUTLET BOX
using the GROUND CLIP (supplied). Position GROUND CLIP
as shown in Fig. 2. Bend wire so unattached end is pointing
away from the OUTLET BOX. (Fig. 3).
using the GROUND CLIP (supplied). Position GROUND CLIP
as shown in Fig. 2. Bend wire so unattached end is pointing
away from the OUTLET BOX. (Fig. 3).
3. Remove K.O. from top of OUTLET BOX and fasten an electri-
cal connector (by others).
4. Place OUTLET BOX on T-BAR(s). If OUTLET BOX does not fit
over the BULB of the T-BAR(s), flatten the BULB with a pair
of pliers.
of pliers.
5. Pass SUPPLY LEADS through electrical connector leaving
approximately 8” of wire beyond the box. WIRES MUST BE
DRESSED AS SHOWN. (Fig. 4)
DRESSED AS SHOWN. (Fig. 4)
6. Fasten 12 AWG solid SUPPLY GROUND WIRE to OUTLET BOX
using a GROUND CLIP (supplied). Position 180° from other
GROUND CLIP. (Fig. 2)
GROUND CLIP. (Fig. 2)
CAUTION:
• TURN OFF POWER AT FUSE BOX BEFORE INSTALLING TRACK.
• DO NOT MAKE ELECTRICAL SPLICES IN OUTLET BOX OF GRID CEILING CANOPY KIT.
• USE SOLID 12 AWG WIRES FOR SUPPLY TO TRACK (NOT STRANDED).
• INSTRUCTIONS FOR GROUNDING MUST BE FOLLOWED. FAILURE TO DO SO MAY RESULT IN AN ELECTRICAL HAZARD.
• DO NOT MAKE ELECTRICAL SPLICES IN OUTLET BOX OF GRID CEILING CANOPY KIT.
• USE SOLID 12 AWG WIRES FOR SUPPLY TO TRACK (NOT STRANDED).
• INSTRUCTIONS FOR GROUNDING MUST BE FOLLOWED. FAILURE TO DO SO MAY RESULT IN AN ELECTRICAL HAZARD.
C
A
B
CEILING & CEILING
PANEL TYPE
GRID CEILING
MOUNTING CLIP
INSTRUCTIONS
15/16”
9/16”
(ORDER SEPARATELY)
6089
CANOPY SPACER
CROSS BAR &
CANOPY
15/16”
9/16”
5/16” to 13/32”
9/16”
1/8 - 1/4”
5/16”
(ORDER SEPARATELY)
6087
USE
USE
USE
USE
USE
USE
(SUPPLIED)
(ORDER SEPARATELY)
6088
FIG. 1
OUTLET
BOX
CROSSBAR
GROUND
WIRE
WIRE
CANOPY
PLATE
PLATE
T-BAR
RECTANGULAR
KO
KO
CANOPY
SPACER
SPACER
BOTTO M
COVER
COVER
THIN HEAD
SCREW
SCREW
VERTICAL KO
FEED TRACK OR
CONNECTOR
CONNECTOR